(2) TORQUE the nut to between 100 and 140 lbf.in (1.13 and 1.58 m.daN).

 (3) Push up the lock release sleeve (55) to engage the end of hold-open rod (50) in the retention bracket (60).

 (4) Lower the fan cowl door and remove the fan cowl sling (5).

 (5) Remove the universal attach pads (15) from the hoist points on the fan cowl door (10).

 (6) Install the filler plugs in the fan cowl door.

 F 『 EEFF : ALL E Page 40771-13-12
 E E Feb 01/98 E E ECES E 5. Close-up

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

________ Subtask 71-13-12-410-050
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the access platform(s).

 (4) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 40871-13-12
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 LATCH - FAN COWL DOOR - REMOVAL/INSTALLATION
____________________________________________ TASK 71-13-13-000-041 Removal of the Fan Cowl Door Latches
 1. Reason for the Job

__________________
 Self Explanatory

 2. Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-13-991-300 Fig. 401
 3. Job Set-up
__________ Subtask 71-13-13-941-050
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
 F 『 EEFF : ALL E Page 40171-13-13
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).
 Subtask 71-13-13-010-050
 B. Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 4. Procedure
_________
 (Ref. Fig. 401/TASK 71-13-13-991-300)
 Subtask 71-13-13-020-050
 A. Removal of the Fan Cowl Door Latches
 (1) Remove the cotter pin (20) from the nut (25). Discard the cotter pin (20).

 (2) Remove the bolt (5), the bushings (10), (35), the washer (30), and the nut (25).

 (3) Remove the latch (40) from the latch housing (15).

 (4) Remove the clevis (65) from the housing unit (45).

 (5) Remove the screws (70), the washers (55) and the nuts (50) that attach the housing (60) from the keeper housing (45).

 (6) Remove the housing (60) from the keeper housing (45).

 F 『 EEFF : ALL E Page 40271-13-13
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Fan Cowl Door and Clevis
 Figure 401/TASK 71-13-13-991-300

 F 『 EEFF : ALL E Page 40371-13-13
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 TASK 71-13-13-400-041

 Installation of the Fan Cowl Door Latches
 CAUTION : ADJUST THE FAN COWL DOORS WHEN A NEW LATCH IS INSTALLED. IF THE FAN
_______ COWL DOORS ARE NOT CORRECTLY ADJUSTED THE DOORS CAN OPEN IN FLIGHT.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 動力裝置 POWER PLANT 1(115)