曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

__________________
 Refer to the MPD TASK: 528101-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R  No specific masking paper
R  No specific masking tape No specific safety barriers No specific warning notices No specific access platform 1.6 m (5 ft. 3 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 11-026 R R Material No. 15-005 R R R Material No. 15-006 R R GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) AIB TN 10138 TYPE I GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00) AIB TN 10138 TYPE I GRADE 3 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
 1EFF : ALL 1 52-81-00Page 601 1 1 Nov 01/02 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-00-00-481-002 Installation of the Safety Devices on the Landing
 Gear Doors 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access 32-12-11-000-001 Removal of the Door Assembly - Main. (for corrective
 action) 32-12-11-400-001 Installation of the Door Assembly - Main. (for corrective action) 52-81-00-991-001 Fig. 601
 3. Job Set-up
__________
 (Ref. Fig. 601/TASK 52-81-00-991-001)
 Subtask 52-81-00-941-050
 A. Safety Precautions
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE
_______
 LANDING GEAR.

 (1)
 Make sure that the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280) is installed on the applicable MLG lockstay actuator (Ref. TASK 32-00-00-481-001).

 (2)
 Put warning notices in position to tell persons not to operate the MLG and the MLG doors.

 (3)
 Put the safety barriers in position.

 1EFF : ALL 1 52-81-00Page 602 1 1 Nov 01/02R 1 1 1CES 1

 MLG Door Attachment-Fittings
 Figure 601/TASK 52-81-00-991-001
 1EFF :  ALL  1  52-81-00 Page 603 
1  1  Feb 01/98
 1  1
 1CES  1

 

 Subtask 52-81-00-010-050
 B. Get Access
 (1) Open the MLG doors (Ref. TASK 32-12-00-010-001).
 (2) Make sure that the GROUND LOCK SLEEVE (460005835) is on the MLG door actuators (Ref. TASK 32-00-00-481-002).
 (3) Put the access platform in position below the inspection area.
 4. Procedure_________
 (Ref. Fig. 601/TASK 52-81-00-991-001)
 Subtask 52-81-00-110-050 
R R A. Preparation For Inspection 
R R  (1) Clean the MLG door forward and aft fitting with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
 Subtask 52-81-00-210-050 
R R  B. Do a visual inspection of the MLG door forward and aft fittings to make sure that: - the paint surface is in a good condition - there are no cracks or distortion - there is no wear or corrosion.
 (1) If necessary, replace the applicable MLG door (Ref. TASK 32-12-11-000-001) and (Ref. TASK 32-12-11-400-001).
 5. Close-up________
 (Ref. Fig. 601/TASK 52-81-00-991-001) 
R  Subtask 52-81-00-916-050 
R  A. Application of Corrosion Preventive Compound 
R R R  WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL_______ MATERIAL. THIS MATERIAL IS DANGEROUS.

 1EFF : ALL 1 52-81-00Page 604 1 1 Nov 01/02 1 1 1CES 1 1EFF : ALL 1 52-81-00Page 605 1 1 Nov 01/02 1 1 1CES 1 TASK 52-81-00-220-001

R R  (1) Cover the area adjacent to the MLG door forward and aft fittings with masking paper and masking tape. 
R R R  (2) Apply a layer of STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to the MLG door forward and aft fittings. 
R R  NOTE : Do not apply the corrosion preventive compound to the bush or____ bearing of each fitting assembly. 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門8(99)