NOTE : Do not safety the lock nut (6) with the tab washer (5) at this
____
stage.
1EFF : 001-049, 051-099, 101-105, 1 52-71-12Page 433 1 1 May 01/05 1 1 1CES 1 Subtask 52-71-12-420-052
B. Installation of the Proximity Sensor
(Ref. Fig. 403/TASK 52-71-12-991-003)
(1)
Put the proximity sensor (2) in its installation position on the latch spigot bracket (3).
(2)
Install the lock washer (9) on the proximity switch (2) and install it in the correct position.
(3)
Install the lock nut (8) on the proximity switch (2) and tighten it.
(4)
Safety the lock nut (8) and the lock washer (9) with lockwire, corrosion-resistant steel, dia 0.6 mm (0.0236 in).
(5)
Remove the blanking caps from the connector (1) of the cable loom and the proximity sensor (2).
(6)
Connect the connector (1) of the cable loom with the proximity sensor (2).
Subtask 52-71-12-820-052
C. Adjustment of the Proximity Switch
(Ref. Fig. 404/TASK 52-71-12-991-004)
(1)
Close and lock the Bulk cargo-compartment door from the inner side (Ref. TASK 52-30-00-860-008).
(2)
Measure the distance "X" between the surface of the target plate (7) and the surface of the latch spigot bracket (3).
NOTE : The distance "X" must be between 44.2 mm (1.7401 in.) and 44.8
____
mm (1.7637 in.).
(3) If the distance "X" is not correct, adjust the proximity target (7) as follows:
(a)
Loosen the lock nut (6) and turn the proximity target (7) until the distance is correct.
(b)
Tighten the lock nut (6) and safety it with the new tab washer (5).
1EFF : 001-049, 051-099, 101-105, 1 52-71-12Page 434 1 1 May 01/05 1 1 1CES 1
Adjustment of Proximity Switch 50WV
Figure 404/TASK 52-71-12-991-004
1EFF : 001-049, 051-099, 101-105, 1 52-71-12Page 435 1 1 May 01/05 1 1 1CES 1 Subtask 52-71-12-865-058
D. Make sure that this(these) circuit breaker(s) is(are) closed:
46WV.
Subtask 52-71-12-710-050
E. Do an operational test to make sure that the function of the proximity switch 50WV is correct (Ref. TASK 52-71-00-710-001).
5. Close-up
________ Subtask 52-71-12-410-053
A. Close Access
(1)
Install the protection cover (12) as follows:
(a)
Put the gasket (10) together with the plate (11) in their installation positions on the floor panel 162KF.
(b)
Put the protection cover (12) in its installation position on the Bulk door frame.
(c)
Install the screws (14) and the washers (13) which attach the protection cover (12) to the Bulk door frame.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Close and lock the Bulk cargo-compartment door (Ref. TASK 52-30-00-860-008).
(4)
Remove the access platform(s).
1EFF : 001-049, 051-099, 101-105, 1 52-71-12Page 436 1 1 May 01/05 1 1 1CES 1 PROXIMITY SWITCH - EMERGENCY EXITS (19WV1,19WV2,21WV1,21WV2)
____________________________________________________________ REMOVAL/INSTALLATION
____________________ TASK 52-71-13-000-001 R Removal of the Proximity Switches (19WV1,19WV2,21WV1,21WV2)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-10-00-010-001 Opening of the Passenger/Crew Door
52-21-11-000-001 Removal of the Emergency Exit Hatch
**ON A/C 001-049, 051-099, 101-149, 201-299,
52-71-13-991-001 Fig. 401 R **ON A/C 151-199, 401-499,
52-71-13-991-001-A Fig. 401A
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 52-71-13Page 401 1201-299, 401-499, 1Config-1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門8(45)
