(1) Put the access platform in position at the applicable passenger/crew door 831 or 841 or 832 or 842.
 (a)
 Open the applicable passenger/crew door (Ref. TASK 52-10-00-010-001).

 (b)
 Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).

 Subtask 52-71-00-020-056
 C. Removal of the Door Lining Panel
 (1) Remove the lining panel:
 FOR 4WN1
 831CZ (Ref. TASK 25-23-46-000-001).

 FOR 4WN2
 841CZ (Ref. TASK 25-23-46-000-001).

 FOR 7WN1
 832CZ (Ref. TASK 25-23-46-000-002).

 FOR 7WN2
 842CZ (Ref. TASK 25-23-46-000-002).

 FOR 13WV1
 831EZ, 831CZ (Ref. TASK 25-23-46-000-001).
 FOR 13WV2
 841EZ, 841CZ (Ref. TASK 25-23-46-000-001).

 FOR 17WV1
 832EZ, 842CZ (Ref. TASK 25-23-46-000-002).

 FOR 17WV2
 842EZ, 842CZ (Ref. TASK 25-23-46-000-002).

 (2) Remove the insulation blanket. Subtask 52-71-00-860-051
 D. Aircraft Maintenance Configuration
 (1)
 Make sure that all the doors are closed.

 (2)
 Do the EIS start procedure (Ref. TASK 31-60-00-860-001)

 1EFF : ALL 1 52-71-00Page 549 1 1 May 01/04R 1 1 1CES 1

 (3) On the ECAM control panel, push the DOOR key:
 -On the lower ECAM DU the DOOR/OXY page comes into view.
 4. Procedure
_________ Subtask 52-71-00-820-053
 A. Adjustment of the Proximity Switches (4WN1, 4WN2, 7WN1, 7WN2)
 WARNING : DO NOT OPEN THE DOOR DURING THE ADJUSTMENT.

_______
 (Ref. Fig. 506/TASK 52-71-00-991-005)

 (1)
 Remove the SAFETY PIN - SLIDE ARMING (98D52103500000).

 (2)
 Put the emergency control handle in the ARMED position.

 (3)
 Remove the nut (3) and the washer (4) or (5) and discard it.

 (4)
 Turn the target (2) until the slide message comes into view in white on the lower ECAM DU.

 NOTE : The target (2) and the proximity switch (1) must not touch.
____
 (5)
 Turn the target (2) in the opposite direction until the slide message goes out of view on the lower ECAM DU.

 (6)
 From this position, screw the target (2) by two turns to two turns and a half .

 (7)
 Apply LUBRICANTS (Material No. 06-005) on the threads of the target (2).

 (8)
 Install a new washer:

 -
FOR 4WN1, 4WN2
 washer (4)

 -
FOR 7WN1, 7WN2
 washer (5)

 (9)
 Install the nut (3).

 (10)
 TORQUE the nut (3) to between 0.3 and 0.4 m.daN (26.54 and 35.39 lbf.in).

 (11)
 Safety the nut (3) with the washer (4) or (5) or (6) or (7).

 (12)
 Put the emergency control handle in the DISARMED position.

 1EFF : ALL 1 52-71-00Page 550 1 1 May 01/04R 1 1 1CES 1

 Adjustment of the Proximity Switches (4WN1, 4WN2, 7WN1, 7WN2, 13WV1, 13WV2,
 17WV1, 17WV2) of the Passeenger/crew Doors
 Figure 506/TASK 52-71-00-991-005

 1EFF : ALL 1 52-71-00Page 551 1 1 May 01/04R 1 1 1CES 1

 (13) Install the SAFETY PIN - SLIDE ARMING (98D52103500000). Subtask 52-71-00-820-079
 B. Adjustment of the Proximity Switches (13WV1, 13WV2, 17WV1, 17WV2)
 WARNING : DO NOT OPEN THE DOOR DURING THE ADJUSTMENT.

_______
 (Ref. Fig. 506/TASK 52-71-00-991-005)

 (1)
 Remove the nut (3) and the washer (6) or (7) and discard it.

 (2)
 Turn the target (2) until the symbol of the door is green on lower ECAM DU.

 NOTE : The target (2) and the proximity switch (1) must not touch.
____
 (3)
 Turn the target (2) in the opposite direction until the symbol of the door is amber on the lower ECAM DU.

 (4)
 From this position, screw the target (2) by two turns to two turns and a half .

 (5)
 Apply LUBRICANTS (Material No. 06-005) on the threads of the target (2).

 (6)
 Install a new washer:

 -
FOR 13WV1, 13WV2
 washer (6)

 -
FOR 17WV1, 17WV2
 washer (7)

 (7)
 Install the nut (3).

 (8)
 TORQUE the nut (3) to between 0.3 and 0.4 m.daN (26.54 and 35.39 lbf.in).

 (9) Safety the nut (3) with the washer (4) or (5) or (6) or (7). Subtask 52-71-00-710-058
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門8(11)