Detailed Inspection of the MLG Door Fittings
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific adjustable access platform 1.5 m (4 ft. 11 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-11-000-001 Removal of the Door Assembly - Main. 32-12-11-400-001 Installation of the Door Assembly - Main. 52-81-00-991-002 Fig. 602 52-81-00-991-003 Fig. 603
1EFF : ALL 1 52-81-00Page 606 1 1 Feb 01/98 1 1 1CES 1 1EFF : ALL 1 52-81-00Page 607 1 1 Nov 01/98 1 1 1CES 1
3. Job Set-up__________
Subtask 52-81-00-941-052
A. Safety Precautions
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE_______ LANDING GEAR.
R R R (1) Make sure that the GROUND LOCK SLEEVE (460005833) or the GROUNDLOCK SLEEVE (460007280) is installed on the MLG lockstay actuators (Ref. TASK 32-00-00-481-001).
(2) Put the safety barriers in position.
Subtask 52-81-00-010-052
B. Get Access
(1) Open the MLG doors (Ref. TASK 32-12-00-010-001).
R R (2) Install the GROUND LOCK SLEEVE (460005835) on the applicable MLG door actuator (Ref. TASK 32-00-00-481-001).
(3) Put the adjustable access platform in position.
(4) Remove the MLG door (Ref. TASK 32-12-11-000-001).
4. Procedure_________
(Ref. Fig. 602/TASK 52-81-00-991-002, 603/TASK 52-81-00-991-003)
Subtask 52-81-00-220-075
A. Dimensional Check of the Aft Hinge Assembly
(1) Between the outer dimension of the bolt (9) and the inner dimension of the flange bush (8).
MLG Door - Location and Detail.
Figure 602/TASK 52-81-00-991-002
1EFF : ALL 1 52-81-00 Page 608
1 1 Feb 01/98
1 1
1CES 1
MLG Door - Fits and Clearances
Figure 603/TASK 52-81-00-991-003
1EFF : ALL 1 52-81-00 Page 609
1 1 Feb 01/98
1 1
1CES 1
-------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | E | 15.966 | 15.984 | | | 15.932 | | | | OD 9 |(0.6285) |(0.6292) | | |(0.6272) | | | | | | | 0.016 | 0.052 | | | 0.120 | | | | | (0.0006)| (0.0020)| | |(0.0047)| | E | 16.000 | 16.018 | | | | 16.052 | | | ID 8 |(0.6299) |(0.6306) | | | |(0.6319) | | -------------------------------------------------------------------------------
Subtask 52-81-00-220-074
B. Dimensional Check of the Aft Hinge Assembly
(1) Between the outer dimension of the flexible bearing (5) and the inner dimension of the bush (6).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門8(100)
