(20) Install the SAFETY PIN - SLIDE ARMING (98D52103500000). Subtask 52-71-00-820-078
B. Adjustment of the Proximity Switches (13WV1, 13WV2, 17WV1, 17WV2)
(Ref. Fig. 505/TASK 52-71-00-991-003)
WARNING : DO NOT OPEN THE DOOR DURING THE ADJUSTMENT.
_______
(1) Make sure that all the doors are closed.
1EFF : ALL 1 52-71-00Page 542 1 1 May 01/04R 1 1 1CES 1
(2)
Disconnect the electrical connector (8) of the proximity switch (1).
(3)
Put blanking caps on the disconnected electrical connectors.
(4)
Connect the CHECKING TOOL-DOORS (355M03210000) to the electrical
connector (8) of the proximity switch (1).
(5)
Remove the nut (3) and the washer (4) or (5) or (6) or (7) and
discard it.
(6)
Turn the target (2) until the NEAR indicator light comes on.
NOTE : The target (2) and the proximity switch (1) must not be in
____
contact.
(7)
Turn the target (2) in the opposite direction until the FAR indicator light comes on.
(8)
From this position, screw the target (2) by two turns to two turns
and a half.
(9)
Apply LUBRICANTS (Material No. 06-005) on the threads of the target (2).
(10)
Install a new washer:
-
FOR 13WV1, 13WV2
washer (6)
-
FOR 17WV1, 17WV2
washer (7)
(11)
Install the nut (3).
(12)
TORQUE the nut (3) to between 0.3 and 0.4 m.daN (26.54 and 35.39 lbf.in).
(13)
Safety the nut (3) with the washer (4) or (5) or (6) or (7).
(14)
Remove the blanking cap from the electrical connector (8).
(15)
Disconnect the CHECKING TOOL-DOORS (355M03210000) from the proximity switch (1).
(16)
Connect the electrical connector (8) of the proximity switch (1).
1EFF : ALL 1 52-71-00Page 543 1 1 May 01/04R 1 1 1CES 1
Subtask 52-71-00-865-076
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 48WV, 13WN, 15WN
Subtask 52-71-00-710-057
D. Operational Test
(1)
FOR 13WV1, 13WV2, 17WV1, 17WV2
-Do an operational test of the warning system related to the passenger/crew doors (Ref. TASK 52-71-00-710-001).
(2)
FOR 4WN1, 4WN2, 7WN1
-Do an operational test of the emergency escape slide of the passenger/crew doors. (Ref. TASK 52-73-00-710-001).
5. Close-up
________ Subtask 52-71-00-420-057
A. Installation of the Door Lining Panel
(1) Install the lining panel:
FOR 4WN1
831CZ (Ref. TASK 25-23-46-400-001).
FOR 4WN2
841CZ (Ref. TASK 25-23-46-400-001).
FOR 7WN1
832CZ (Ref. TASK 25-23-46-400-002).
FOR 7WN2
842CZ (Ref. TASK 25-23-46-400-002).
FOR 13WV1
831EZ, 831CZ (Ref. TASK 25-23-46-400-001).
FOR 13WV2
841EZ, 841CZ (Ref. TASK 25-23-46-400-001).
FOR 17WV1
832EZ, 832CZ (Ref. TASK 25-23-46-400-002).
1EFF : ALL 1 52-71-00Page 544 1 1 May 01/04R 1 1 1CES 1
FOR 17WV2
842EZ, 842CZ (Ref. TASK 25-23-46-400-002).
Subtask 52-71-00-410-073
B. Close Access
(1)
Obey the special precautions after the work on the passenger/crew door (Ref. TASK 52-10-00-860-002).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Close the applicable passenger/crew door 831 or 841 or 832 or 842 (Ref. TASK 52-10-00-410-001).
(4) Remove the access platform(s). Subtask 52-71-00-862-061
C. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
1EFF : ALL 1 52-71-00Page 545 1 1 May 01/04R 1 1 1CES 1
TASK 52-71-00-820-002- 01
Adjustment of the Proximity Switches (4WN1, 4WN2, 7WN1, 7WN2, 13WV1, 13WV2, 17WV1, 17WV2) of the Passenger/Crew Doors with the ECAM DU.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R RR R No specific No specific FOR FIN 7WN1, 7WN2 No specific access platform 3.5 m (11 ft. 6 in.) Torque Wrench : range 0.00 to 1.20 m.daN (0.00 to 9.00 lbf.ft) Torque Wrench : range 0.00 to 1.20 m.daN (0.00 to 9.00 lbf.ft)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門8(9)
