1EFF : ALL 1 34-36-18Page 407 1 1 May 01/05 1 1 1CES 1
(4) Do an inspection of the component interface and/or the adjacent area.
4. Procedure
_________ (Ref. Fig. 401/TASK 34-36-18-991-001) WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THE SPECIAL
_______
MATERIAL.
THIS MATERIAL IS DANGEROUS.
Subtask 34-36-18-420-050
A. Installation of the Glide/Slope Antenna
(1)
Apply SPECIAL MATERIALS (Material No. 05-013) to the bulkhead (4) where you install the antenna and to the antenna (1) mount.
(2)
Apply SEALANTS (Material No. 09-019) to the bulkhead (4) where you install the antenna and to the antenna (1) mount (Ref. TASK 51-76-11-300-001).
NOTE : Make sure that there is no sealant in the screws holes.
____
(3)
Remove the blanking caps from the coaxial connectors (3) and (5).
(4)
Put the O-rings (2) in the correct position on the antenna (1).
(5)
Connect the coaxial connectors (3) to the antenna (1).
(6)
Put the antenna (1) in position on the bulkhead (4).
(7)
Attach the antenna (1) with the screws (6).
(8)
Remove the sealant which is not necessary.
(9)
Apply a sealing bead with SEALANTS (Material No. 09-016) around the antenna (1).
(10) Make the antenna contour smooth.
Subtask 34-36-18-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s): R 1RT1, 1RT2, 5SQ1, 5SQ2
1EFF : ALL 1 34-36-18Page 408 1 1 May 01/05 1 1 1CES 1
R **ON A/C 001-004, 051-060,
Subtask 34-36-18-720-050
C. Do the functional test of the two ILS (para. Reception test with tool) (Ref. TASK 34-36-00-720-001). **ON A/C ALL
R Post SB 34-1147 For A/C 001-004,051-060, Subtask 34-36-18-720-050-A
C. Do the functional test of the two MMRs (para. Reception test with tool) (Ref. TASK 34-36-00-720-002).
**ON A/C ALL
5. Close-up
________
Subtask 34-36-18-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the radome 110AL (Ref. TASK 53-15-11-410-001).
(3)
Remove the access platform(s).
(4)
Remove the warning notice(s).
1EFF : ALL 1 34-36-18Page 409 1 1 May 01/05 1 1 1CES 1
RECEIVER - ILS (2RT1,2RT2) - REMOVAL/INSTALLATION
_________________________________________________ TASK 34-36-31-000-001 Removal of the ILS Receiver (2RT1,2RT2)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
34-36-31-991-001 Fig. 401
3. Job Set-up
__________ Subtask 34-36-31-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 2RT1
49VU NAV/ILS/1 1RT1 G12 FOR 2RT2 121VU COM NAV/ILS/2 1RT2 K09
R 1EFF : 001-004, 051-060, 1 34-36-31Page 401 1 1 Config-1 May 01/05 1 1 1CES 1 Subtask 34-36-31-010-050
B. Get Access
(1)
Put the access platform in position at the access door 811 in zone
122.
(2)
Open the access door 811.
4. Procedure
_________
(Ref. Fig. 401/TASK 34-36-31-991-001) Subtask 34-36-31-020-050
A. Removal of the ILS Receiver (2RT1, 2RT2)
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航3(22)
