2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 1.6 m (5 ft. 3 in.) YV68A110 1 PORTABLE DATA LOADER
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 31-32-00-860-010 Procedure to Get Access to the SYSTEM REPORT/TEST NAV
 Page 52-41-00-410-002 Close the Avionics Compartment Doors after Access 34-43-00-991-001 Fig. 301
 3. Job Set-up
__________ Subtask 34-43-00-861-051
 A. Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
R 1EFF : ALL 1 34-43-00Page 301 1 1 Aug 01/05 1 1 1CES 1 Subtask 34-43-00-860-071

 B. On the PORTABLE DATA LOADER (YV68A110), make sure that the ON/OFF switch is at OFF.
 Subtask 34-43-00-010-052
 C. Get Access
 (1) Put the access platform in position at the access door 824 in zone
 128.
 (2) Open the access door 824. Subtask 34-43-00-865-067
 D. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU COM NAV/TCAS 4SG K10
 Subtask 34-43-00-860-072
 E. Aircraft Maintenance Configuration
 (1)
 On the panel 188VU
 (Ref. Fig. 301/TASK 34-43-00-991-001)

 (a)
 Remove the blanking cap from the DATA LOADER connector 194VC.

 (b)
 Connect the cable of the portable data loader to the DATA LOADER connector 194VC.

 (2)
 Make sure that the aircraft is in ground configuration.

R 1EFF : 001-049, 051-061, 101-105, 1 34-43-00Page 302 1 1 May 01/05 1 1 1CES 1

 Data Loader Connector
 Figure 301/TASK 34-43-00-991-001

R 1EFF : 001-049, 051-099, 101-105, 1 34-43-00Page 303 1 1 Aug 01/05 1 1 1CES 1 Subtask 34-43-00-865-068

 F. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/MCDU/1 11CA1 B01 49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU CFDS/CFDIU/SPLY 2TW J18 121VU CFDS/CFDIU/BACK/UP 8TW J17 121VU AUTO FLT/MCDU/2 11CA2 N20 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35
 Subtask 34-43-00-865-069
 G. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 4SG.
 4. Procedure
_________
 Subtask 34-43-00-970-052
 A. Loading of the Operational Software
 NOTE : After the uploading operations, you must do a check on the MCDU,
____
 of the reference of the data loaded in the computer.

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the portable data loader:
-set the ON/OFF switch to ON.
-put the disk into the disk drive, the label in the forward direction.
On the portable data loader:
-
the < < MDDU READY > > indication comes into view.

-
the READY indication comes into view

-
then, the WAIT RESPONSE indicationcomes into view

 -
then, the TRANSF IN PROG indication comes into view.

R 1EFF : 001-049, 051-061, 101-105, 1 34-43-00Page 304 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------NOTE : If more than one disk is
____ necessary, the EJECT DISK and INSERT NEXT DISK indications come into view one after the other. They tell you to put a new disk in the portable data loader.
 -when all the data are in the computer, the TRANSF COMPLETE indication comes into view.
 -eject the disk from the disk  - the < < MDDU READY > > indication drive. comes into view.
 Subtask 34-43-00-280-055
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航3(135)