1EFF : ALL 1 34-43-00Page 17 1 1 Aug 01/05 1 1 1CES 1
TCAS Computer Figure 005
R 1EFF : 1 1 1CES 001-049, 101-105, 151-199, 1 111 34-43-00 Page 18 May 01/05
R TCAS Computer
R Figure 005A
R 1EFF : 051-054, 1 34-43-00 Page 19
1 1 May 01/05
1 1
1CES 1
TCAS Computer
Figure 005B
R 1EFF : 106-149, 201-209, 211-299, 301-399, 1 34-43-00Page 20 1401-499, 1Aug 01/05 1 1 1CES 1
R TCAS Computer
R Figure 005C
R 1EFF : 051-099, 1 34-43-00 Page 21
1 1 May 01/05
1 1
1CES 1
R TCAS Computer Figure 005D
R 1EFF : 1 1 1CES 201-207, 210-210, 1 111 34-43-00 Page 22 May 01/05
TCAS Computer - Block Diagram
Figure 006
R 1EFF : 001-049, 101-105, 151-199, 1 34-43-00Page 23 1 1 May 01/05 1 1 1CES 1 (2) Radio frequency section
(a)
General The RF section consists of receiver, transmitter and RF switch portions. The receiver processes the raw ATCRBS or Mode S intruder reply data received from either the top or bottom antenna. The transmitter portion of the RF section interrogates intruders once per second, also using either antenna. The RF switch portion selects the antenna (top or bottom) for the transmission and reception of the TCAS signals. For ATCRBS intruders, interrrogations are accomplished by controlling a "whisper shout" attenuation system which provides successive responses, starting with the nearest aircraft and continuing progressively to those farther away so as to avoid saturating the radio-electric space and resulting interference.
(b)
RF switch
The RF switch is dual-purpose:
-
it switches the transmission/reception circuits between the top and bottom antennas
-
it directs antenna links either to the transmit circuits or to the receive circuits as the antenna links and elements are used indifferently for transmission and reception.
The four elements of each antenna are connected to hyperfrequency multiplexers controlled by the video controller.
(c)
Transmitter The transmitter generates the 1030 MHz carrier frequency required for TCAS transmission. For a Mode S interrogation, this frequency is modulated in DPSK (Data Phase Shift Keyed) format by the video controller module. For Mode C interrogations the frequency is applied to the whisper shout attenuator which attenuates the signal from 0 to 32 dB in 1 dB increments. The modulated frequency is then split into four parts by a programmable circuit controlled by the video controller so as to divide transmitter output into four separate antenna-element drive channels.
(d)
Receiver The receive circuitry consists of three RF channels. The signals are received through the antenna elements and processed as pairs. The paths of the signals between antenna element pairs and receiver pairs are exchanged by swap switches to eliminate the phase error in the different circuits. In each receiver, the RF signal is mixed with the local oscillator signal to produce a 60 MHz intermediate frequency signal.
1EFF : 001-049, 101-105, 151-199, 1 34-43-00Page 24 1 1 Aug 01/05R 1 1 1CES 1
The processed signals are applied to phase detectors that determine the sine and cosine relationship between antenna element pairs. After amplification, these signals are transmitted to the video processor where relative bearing is determined. Logarithmic outputs from the three receivers are also applied to a log summer which passes the log sum signal to the video processor where it is decoded to determine range and altitude.
(3) Not Applicable
**ON A/C 051-099,
A. TCAS Computer
(1) Introduction
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導(dǎo)航3(100)
