R 1EFF : 106-149, 201-299, 301-399, 401-499, 1 34-43-11Page 416 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
Subtask 34-43-11-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 4SG
Subtask 34-43-11-740-050
C. Do the BITE test of the TCAS (Ref. TASK 34-43-00-740-001)
5. Close-up
________ Subtask 34-43-11-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
For 7SG1 only.
Remove the access platform(s).
1EFF : ALL 1 34-43-11Page 417 1 1 May 01/05 1 1 1CES 1 COMPUTER - TCAS (1SG) - REMOVAL/INSTALLATION
____________________________________________
TASK 34-43-34-000-001
Removal of the TCAS Computer (1SG)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
34-43-34-991-001 Fig. 401
3. Job Set-up
__________
Subtask 34-43-34-865-050
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
121VU COM NAV/TCAS 4SG K10
1EFF : ALL 1 34-43-34Page 401 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
Subtask 34-43-34-010-050
B. Get Access
(1)
Put the access platform in position at the access door 824 in zone 128
(2)
Open the access door 824.
4. Procedure
_________
Subtask 34-43-34-020-050
A. Removal of the TCAS Computer
(Ref. Fig. 401/TASK 34-43-34-991-001)
(1)
Loosen the nuts (4).
(2)
Lower the nuts (4).
(3)
Pull the TCAS computer (1) on its rack (3) to disconnect the electrical connectors (2).
(4)
Remove the TCAS computer (1) from its rack (3).
(5)
Put blanking caps on the disconnected electrical connectors (2).
1EFF : ALL 1 34-43-34Page 402 1 1 Aug 01/05 1 1 1CES 1
TCAS Computer
Figure 401/TASK 34-43-34-991-001
1EFF : ALL 1 34-43-34 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 34-43-34-400-001
Installation of the TCAS Computer (1SG)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.6 m (5 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
34-43-00-740-001 BITE Test of the TCAS R 52-41-00-410-002 Close the Avionics Compartment Doors after Access 34-43-34-991-001 Fig. 401
3. Job Set-up
__________
Subtask 34-43-34-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is in position at the access door 824 in zone 128.
(2)
Make sure that the access door 824 is open.
1EFF : ALL 1 34-43-34Page 404 1 1 Feb 01/02 1 1 1CES 1 Subtask 34-43-34-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM NAVIGATION 導(dǎo)航3(148)
