C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
FOR FIN 6LV 14 seal 33-48-12 01 -040 14 seal 33-48-12 02 -110 22 seal 33-48-12 01 -030 22 seal 33-48-12 02 -030 FOR FIN 7LV 32 seal 33-48-11 01 -030 32 seal 33-48-11 01A-030 34 seal 33-48-11 01 -040 34 seal 33-48-11 01 -110 34 seal 33-48-11 01A-040 34 seal 33-48-11 01A-110
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-21-11-911-001 Tightening Torques for Standard Threaded Fasteners
20-28-00-912-004 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-
33-48-11-400-001 Installation of the Upper Beacon/Strobe Light 7LV from the Outside of the Fuselage 33-48-12-400-001 Installation of the Lower Beacon/Strobe Light 6LV from the Fuselage Outside
R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
33-48-00-991-001-A Fig. 401
**ON A/C 051-051,
33-48-00-991-001 Fig. 401A **ON A/C ALL
3. Job Set-up
__________
Subtask 33-48-00-941-053
A. Aircraft Maintenance Configuration
(1)
Make sure that the WARNING NOTICE is in position to tell persons not to operate the anti-collision lights.
(2)
For the upper anti-collision light:
-Put the ACCESS PLATFORM 6M (20 FT) in position at the upper anti-collision light.
Subtask 33-48-00-865-053
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU LIGHTING/EXT LT/BEACON/UPPER 1LV U06 122VU LIGHTING/EXT LT/BEACON/LOWER 5LV U03
4. Procedure
_________ R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 401/TASK 33-48-00-991-001-A)
**ON A/C 051-051,
(Ref. Fig. 401A/TASK 33-48-00-991-001)R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 33-48-00-440-050-A
A. Reactivation of the Anti-Collision Lights
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
NOTE : For the torque values of the screws see the related AMM 20-21-11
____
(Ref. TASK 20-21-11-911-001).
(1)
Remove the tape from the related anti-collision light.
(2)
Remove the tape from the cable hole in the housing (15) of the anti-collision light.
(3)
Clean the component interface and/or the adjacent area.
(4)
Remove the countersunk screws (3) from the housing (15).
(5)
Lift the housing (15) until you can see the electrical connector (9).
(6)
Disconnect the electrical connector (9) from the housing (15) and support the electrical connector (9).
(7)
Replace the seal:
FOR 6LV
discard the seal (14) and install a new seal (14).
FOR 7LV
discard the seal (34) and install a new seal (34).
(8)
Make sure that the electrical connectors are clean and in the correct condition.
(9)
Connect the electrical connector (9) to the housing (15).
(10)
Remove the screws (5) and the plate (4) from the housing (15).
(11)
Remove the screw (6) and the transformer (7) from the housing (15).
(12)
Support the transformer (7).
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 33-48-00Page 413 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(42)
