(3)
Make sure that the filament of the lamp and the lens are in the correct condition.
R R (4) Remove the blanking cap from the electrical connector (5) and from the support.
R R (5) Make sure that the electrical connector (5) is in the correct condition.
R (6) Connect the electrical connector (5) to its support.
R R (7) Put the optical unit (4) in position on its support (3). Hold it in this position.
R (8) Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (1).
R R (9) Install the optical unit (4) with the two screws (1) and the washers (2).
R (10) Adjust the turnoff light (Ref. TASK 33-43-11-730-001).
R **ON A/C ALL
Subtask 33-43-11-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): FOR 3LC1 - 1LC1. FOR 3LC2 - 1LC2.
Subtask 33-43-11-710-051
C. Operational Test of the Runway Turnoff Lights
(1) Do the operational test of the runway turnoff lights (Ref. TASK 33-43-00-710-001).
5. Close-up________
Subtask 33-43-11-942-050
A. Make sure that the work area is clean and clear of tool(s) and other items.
TASK 33-43-11-000-002 Removal of the Lamp of the Runway Turnoff Light (3LC1, 3LC2) WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
_______ AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-43-11-991-003 Fig. 402
1EFF : ALL 1 33-43-11Page 407 1 1 May 01/05R 1 1 1CES 1
3. Job Set-up
__________ Subtask 33-43-11-865-055
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3LC1
122VU LIGHTING/EXT LT/RWY TURN OFF/L 1LC1 W06 FOR 3LC2 122VU LIGHTING/EXT LT/RWY TURN OFF/R 1LC2 W05
4. Procedure
_________
(Ref. Fig. 402/TASK 33-43-11-991-003) Subtask 33-43-11-020-053
A. Removal of the Lamp
(1)
For the lamp (4):
(a)
Remove the screw (1).
(b)
Remove the retainer (2).
(c)
If the gasket (3) on the retainer (2) is defective, remove and discard it.
(d)
Pull the lamp (4) away from the support (6) and disconnect the two electrical terminals (5).
(e)
Remove the lamp (4).
(2)
For the lamp (4) (alternate configuration):
(a)
Remove the screw (8), the washer (7) and the insulating washer (9).
(b)
Remove the retainer (2).
(c)
Pull the lamp (4) away from the support (6).
(d)
Disconnect the two electrical terminals (5).
1EFF : ALL 1 33-43-11Page 408 1 1 May 01/05R 1 1 1CES 1
Lamp of the Runway Turnoff Light Figure 402/TASK 33-43-11-991-003
1EFF : 1 1R 1CES ALL 1 11 1 33-43-11 Page 409 May 01/05
(e)
Remove the lamp (4).
(f)
If the gasket (3) on the support (6) is defective, remove and discard it.
1EFF : ALL 1 33-43-11Page 410 1 1 May 01/05R 1 1 1CES 1
TASK 33-43-11-400-002
Installation of the Lamp of the Runway Turnoff Light (3LC1, 3LC2)
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT._______
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS._______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(15)
