-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-46-00-710-001 Operational Test of the Taxi and Take Off Lights 33-46-11-991-003-A Fig. 402
3. Job Set-up
__________ Subtask 33-46-11-865-058
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/TAXI AND TAKE OFF/TO 3LR W07
4. Procedure
_________
(Ref. Fig. 402/TASK 33-46-11-991-003-A) Subtask 33-46-11-020-054-A
A. Removal of the lamp
CAUTION : MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU
_______ DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(1)
Remove the screw (1).
(2)
Remove the retainer (2).
(3)
Pull the lamp (3) away from the support (6) and disconnect the three electrical terminals (5).
(4)
Remove the lamp (3).
(5)
If the gasket (4) on the support (6) is defective, remove and discard it.
1EFF : ALL 1 33-46-11Page 410 1 1 May 01/05R 1 1 1CES 1
Lamp of the Take off Light
Figure 402/TASK 33-46-11-991-003-A
1EFF : ALL 1 33-46-11 Page 411
1 1 May 01/05
1 1
1CES 1
Subtask 33-46-11-420-054-A
B. Installation of the lamp
(1) If necessary, install and bond a new gasket (4) in place on the support (6).
(2) Connect the three electrical terminals (5) to the new lamp (3) and install it in position on its support (6). Hold it in this position.
CAUTION : MAKE SURE THAT THE GASKET IS IN THE CORRECT POSITION. IF_______ NOT, YOU CAN DECREASE THE LIFE OF THE LAMP.
R (3) Put the retainer (2) in position.
R R (4) Install and tighten the screw (1) until the lamp (3) is held in position.
R R NOTE : Make sure that there are no visual signs of distortion of the____ retainer (2).
Subtask 33-46-11-865-059
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3LR
Subtask 33-46-11-710-053
D. Operationnal test of the Light
(1) Do the operational test of the Take off Light (Ref. TASK 33-46-00-710-001).
5. Close-up________
Subtask 33-46-11-942-053
A. Make sure that the work area is clean and clear of tool(s) and other items.
LIGHT - TAKE OFF (7LR) - ADJUSTMENT/TEST
________________________________________
TASK 33-46-11-730-001
Adjustment of the Take Off Light (7LR)
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
_______ AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific strap 98D33403500000 1 ADJUSTING TOOL - TAKE OFF LIGHT
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 19-010 USA AMS 5687 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
08-22-00-200-001 Precise Leveling 33-46-11-991-004 Fig. 501
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(25)
