(Ref. Fig. 401A/TASK 33-46-11-991-001) R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 33-46-11-420-050
A. Installation of the Take Off Light
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the filament of the bulb and the lens of the optical unit are in the correct condition.
(4)
Make sure that the clamp is correctly installed.
(5)
Put the light (10) on its support (3).
(6)
Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (1) and (9).
(7) Install the light (10) in the lower fork of the support (3).
(8) Put the washer (8) on the screw (9).
(9) Install the screws in the support (3).
(10) Install the washer (7) and tighten the nut (6).
(11) Turn the light to the upper forks.
(12) Put the washers (2) on the screws (1).
(13) Install the screws in the support (3).
(14) Install the washer (4) and tighten the nut (5).
(15) Remove the blanking caps from the electrical connector (12) and the socket (11).
(16) Make sure that the electrical connector (12) and the socket (11) are in the correct condition.
(17) Connect the electrical connector (12) to the socket (11) and lock it.
R **ON A/C 051-051,
R Subtask 33-46-11-420-050-A
R A. Installation of the Take Off Light
R (1) Clean the component interface and/or the adjacent area.
R (2) Do an inspection of the component interface and/or the adjacent area.
R R (3) Make sure that the filament of the bulb and the lens of the optical unit are in the correct condition.
R (4) Make sure that the clamp is correctly installed.
R (5) Put the light (10) on its support (3).
R R (6) Apply SPECIAL MATERIALS (Material No. 05-002) to the screws (1) and (9).
R (7) Install the light (10) in the lower fork of the support (3).
R (8) Put the washer (8) on the screw (9).
R (9) Install the screws in the support (3).
R (10) Install the washer (7) and tighten the nut (6).
R (11) Turn the light to the upper forks.
R (12) Put the washers (2) on the screws (1).
R (13) Install the screws in the support (3).
R (14) Install the washer (4) and tighten the nut (5).
R (15) Adjust the take off light (Ref. TASK 33-46-11-730-001).
R R (16) Remove the blanking caps from the electrical connector (12) and the socket (11).
R R (17) Make sure that the electrical connector (12) and the socket (11) are in the correct condition.
R (18) Connect the electrical connector (12) to the socket (11) and lock it.
R **ON A/C ALL
Subtask 33-46-11-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3LR
Subtask 33-46-11-710-051
C. Operational Test of the Light
(1) Do the operational test of the Take off Light (Ref. TASK 33-46-00-710-001).
5. Close-up________
Subtask 33-46-11-942-050
A. Make sure that the work area is clean and clear of tool(s) and other items.
TASK 33-46-11-960-001
Replacement of the Lamp in the Take Off Light (7LR)
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
_______
AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(24)
