TASK 33-46-12-960-001
Replacement of the Lamp in the Taxi Light (8LR)
WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
_______
AFTER YOU DE-ENERGIZE THE ELECTRICAL CIRCUITS.
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) R No specific 1 ALLEN KEY 3/32 IN
B. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
5 lamp 33-46-12 01A-050 6 gasket 33-46-12 01A-060
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-46-00-710-001 Operational Test of the Taxi and Take Off Lights 33-46-12-991-003 Fig. 402
3. Job Set-up
__________
Subtask 33-46-12-865-058
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU LIGHTING/EXT LT/TAXI AND TAKE OFF/TAXI 1LR W08
4. Procedure_________
Subtask 33-46-12-020-054
A. Removal of the Lamp (Ref. Fig. 402/TASK 33-46-12-991-003)
R (1) Remove the washer (2).
R R (2) Remove the screw (1) with an ALLEN KEY 3/32 IN and the insulating washer (3).
R (3) Remove the clamp (4).
R (4) Pull the lamp (5) away from the support (8) and disconnect the two electrical terminals (7).
R (5) Remove the lamp (5).
R (6) If the gasket (6) on the support (8) is defective, remove and discard it.
Subtask 33-46-12-420-054
B. Installation of the lamp (Ref. Fig. 402/TASK 33-46-12-991-003)
(1) If necessary, install a new gasket (6) in position on its support (8).
(2) Connect the two electrical terminals (7) to the new lamp (5) and install it in position on its support (8). Hold it in this position.
(3) Put the clamp (4) in position.
Lamp of the Taxi Light
Figure 402/TASK 33-46-12-991-003
1EFF : ALL 1 33-46-12 Page 413
1 1 May 01/05
1 1
1CES 1
R R R (4) Manually compress the clamp (4) to move the two brackets nearer together and install the screw (1) with an ALLEN KEY 3/32 IN. Tighten by two turns and do not cause visual signs of distortion of the two brackets.
Subtask 33-46-12-865-059
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LR
Subtask 33-46-12-710-053
D. Operational Test of the Taxi Light
(1) Do the operational test of the taxi light (Ref. TASK 33-46-00-710-001).
5. Close-up________
Subtask 33-46-12-942-053
A. Make sure that the work area is clean and clear of tool(s) and other items.
LIGHT - TAXI (8LR) - ADJUSTMENT/TEST
____________________________________ TASK 33-46-12-730-001 Adjustment of the Taxi Light (8LR) WARNING : WEAR GLASSES AND PROTECTIVE CLOTHING WHEN YOU WORK ON THE LIGHT.
_______
WARNING : DO NOT DISCONNECT THE ELECTRICAL CONNECTIONS FOR AT LEAST 2 MINUTES
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光2(29)
