(2)
Remove the four screws (4) and washers (3) that attach the dome light box.
(3)
Put a blanking caps on the disconnected electrical connector (1) and the socket (2).
(4)
Remove the dome light box.
Dome Light
Figure 401/TASK 33-12-11-991-001
1EFF : ALL 1 33-12-11 Page 403
1 1 Feb 01/98
1 1
1CES 1
Subtask 33-12-11-020-055
C. Removal of the socket
(1)
Remove the bulb (10).
(2)
Remove the two screws (14) and the two screws (5) with their nuts
(15) that attach the plate (6) to the defective socket (9). Hold the plate during the removal.
(3)
Remove the plate (6).
(4)
Remove the screw (12), the washer (13) and the power supply cable (11).
(5)
Remove the nut (7) and the washer (8).
(6)
Remove the defective socket (9).
TASK 33-12-11-400-002
Installation of the Cockpit Dome Light (161LE, 162LE, 163LE, 164LE, 165LE, 166LE, 167LE, 168LE)
CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific ALLEN wrench
B. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
R 10 bulb 33-12-08 01 -090 10 bulb 33-12-08 01C-090
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
33-12-00-710-001 Operational Test of the General Illumination
33-12-11-991-001 Fig. 401
3. Job Set-up
__________
Subtask 33-12-11-865-056
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU LIGHTING/EMER LT/CKPT/DOME 1LE H08 122VU LIGHTING/CKPT/DOME 3LE Y06
4. Procedure
_________
(Ref. Fig. 401/TASK 33-12-11-991-001) Subtask 33-12-11-160-051
A. Preparation for the installation
(1)
Clean the component interface and/or the adjacent area.
(2)
Make an inspection of the component interface and/or the adjacent area.
Subtask 33-12-11-420-053
B. Installation of the bulb
(1)
Install the bulb (10).
(2)
Install the ceiling panel (211CC for the Captain Dome Lights and 212CC for the F/O Dome Lights) with an ALLEN wrench.
Subtask 33-12-11-420-054
C. Installation of the dome light box
(1)
Remove the blanking caps of the disconnected electrical connector (1) and the socket (2).
(2)
Install the dome light box.
(3)
Tighten the four screws (4) and washers (3) that attach the dome light box.
1EFF : ALL 1 33-12-11Page 406 1 1 May 01/00R 1 1 1CES 1
(4)
Connect the electrical connector (1) to the socket (2).
(5)
Install the ceiling panel (211CC for the Captain Dome Lights and 212CC for the F/O Dome Lights) with an ALLEN wrench.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光1(29)
