(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
INTENTIONALLY BLANK
R 1 1
33-41-00Page 410
1 1 Feb 01/04 1 1 1CES 1
TASK 33-41-00-440-001 Reactivation of the Glazing Panel of the Wing-Tip Navigation Light WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the CDL TASK: 33-6
Wing tip navigation light glazing
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 4.35 m (14 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-37-12-000-001 Removal of the Navigation Light Glazing Panel 57-37-12-400-001 Installation of the Navigation Light Glazing Panel
3. Job Set-up
__________ Subtask 33-41-00-941-051
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice on panel 25VU to tell persons not to operate the navigation lights or the strobe lights.
1EFF : ALL 1 33-41-00Page 411 1 1 May 01/02R 1 1 1CES 1
(3) Put the access platform below the applicable zone 534 (634). Subtask 33-41-00-865-054
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU LIGHTING/EXT LT/NAV1/AND LOGO/LT 1LA T03 122VU LIGHTING/EXT LT/NAV2/AND LOGO/LT 2LA T02 122VU LIGHTING/WING/STROBE 10LV V05
4. Procedure
_________ Subtask 33-41-00-440-050
A. Reactivation of the Glazing Panel of the Wing-Tip Navigation Light
(1) Replace the wing-tip navigation light glazing panel (Ref. TASK 57-37-12-000-001), (Ref. TASK 57-37-12-400-001).
5. Close-up
________ Subtask 33-41-00-865-055
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LA, 2LA, 10LV.
Subtask 33-41-00-942-051
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safaty barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(6)
Write in the aircraft technical log that the glazing panel of the wing-tip navigation light has been replaced.
1EFF : ALL 1 33-41-00Page 412 1 1 May 01/02R 1 1 1CES 1
TASK 33-41-00-040-002 Deactivation of the Lens of the Tail Navigation Light WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the CDL TASK: 33-3
Rear navigation light lens (glazing)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LIGHTS 燈光1(140)
