(4)
 Make sure that the end of the seal (5) is 10 +2.5 -2.5 mm (0.3937 +0.0984 -0.0984 in.) from the edge of the door.

 (5)
 Install the four screws (11) and TORQUE them to 0.35 m.daN (30.97 lbf.in).

 (6)
 Put the lightning arrester strip (8), the seal (3) and the retainer assembly (2) in position.

 (7)
 Make sure that the end of the lightning arrester strip (8) is 2 mm (0.0787 in.) from the edge of the door.

 (8)
 Make sure that the end of the seal (3) is 10 +2.5 -2.5 mm (0.3937 +0.0984 -0.0984 in.) from the edge of the door.

 (9)
 Install the three screws (13) and TORQUE them to 0.35 m.daN (30.97 lbf.in).

 (10)
 Put the seals (9), (12), and the seal retainer assembly (6) in position.

 (11)
 Make sure that the end of the seals (9) and (12) is 10 +2.5 -2.5 mm (0.3937 +0.0984 -0.0984 in.) from the edge of the door.

 (12)
 Install the eleven screws (10) and TORQUE them to 0.35 m.daN (30.97 lbf.in).

 1EFF : ALL 1 32-22-11Page 424 1 1 May 01/03R 1 1 1CES 1

 (13)
 Put the seal (14) and the seal retainer assembly (7) in position.

 (14)
 Make sure that the end of the seal (14) is 10 +2.5 -2.5 mm (0.3937 +0.0984 -0.0984 in.) from the edge of the door.

 (15)
 Install the four screws (15), the nine screws (17) and TORQUE them to

 0.35 m.daN (30.97 lbf.in).

 (16)
 Put the seal (19) and the seal retainer assembly (24) in position.

 (17)
 Make sure that the end of the seal (19) is 10 +2.5 -2.5 mm (0.3937 +0.0984 -0.0984 in.) from the edge of the door.

 (18)
 Install the four screws (18) and TORQUE them to 0.35 m.daN (30.97 lbf.in).

 (19)
 Put the seal (22) and the seal retainer assembly (25) in position.

 (20)
 Make sure that the end of the seal (22) is 10 +2.5 -2.5 mm (0.3937 +0.0984 -0.0984 in.) from the edge of the door.

 (21)
 Install the three screws (20) and TORQUE them to 0.35 m.daN (30.97 lbf.in).

 (22)
 Put the lightning arrester strip (23), the seal (26), and the seal retainer assembly (27) in position.

 (23)
 Make sure that the end of the lightning arrester strip (23) is 2 mm (0.0787 in.) from the edge of the door.

 (24)
 Install the twenty-one bolts (21) and the twenty-one nuts (1) and TORQUE them to 0.35 m.daN (30.97 lbf.in).

 5. Close-up
________ Subtask 32-22-11-942-057
 A. Removal of Equipment
 (1)
 Remove the access platform(s).

 (2)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 (3)
 Remove the warning notice(s).

 1EFF : ALL 1 32-22-11Page 425 1 1 May 01/03R 1 1 1CES 1

 Subtask 32-22-11-410-054
 B. Close Access
 (1) Close the nose landing-gear doors (Ref. TASK 32-22-00-410-001).
 1EFF : ALL 1 32-22-11Page 426 1 1 May 01/03R 1 1 1CES 1

 TASK 32-22-11-010-001 Removal of the Main Door Assy for Access WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
 1. Reason for the Job
__________________
 This procedure is only applicable when the main door assy is removed for access. For the applicable procedure to remove the main door assy for replacement, Ref. TASK 32-22-11-000-001.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
 No specific warning notice(s)
 No specific access platform 1.7 m (5 ft. 7 in.)

 B. Referenced Information -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------32-22-00-010-001 Nose Gear Doors - Ground Doors Opening **ON A/C 001-049, 051-099, 101-105, 151-199, 201-212,
 32-22-11-991-010 Fig. 405 R **ON A/C 106-149, 213-299, 301-399, 401-499,
 32-22-11-991-010-A Fig. 405A
 1EFF : ALL 1 32-22-11Page 427 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 32-22-11-941-058

 A. Safety Precautions
 (1) In the cockpit, on the panel 400VU, put warning notice(s) in position to tell persons not to operate the landing gear control lever.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架4(7)