R  (c) Seal the drain holes of the pitot probe 9DA1 with colored 
R  adhesive tape. 
R  CAUTION : WHEN YOU SEAL THE DRAIN HOLE IN THE PITOT PROBE, DO NOT_______ 
R  SEAL THE HOLE DIRECTLY WITH THE COLORED ADHESIVE TAPE. 
R  ALWAYS PUT A PIECE OF PLASTIC ON THE HOLE AND USE THE 
R  TAPE TO ATTACH THE PLASTIC. 
R  IF YOU SEAL THE DRAIN HOLE DIRECTLY WITH THE ADHESIVE 
R  TAPE, THERE IS A RISK THAT SOME OF THE ADHESIVE WILL 
R  STAY ON THE HOLE AND COLLECT PARTICLES. THIS CAN 
R  SUBSEQUENTLY CAUSE BLOCKAGE OF THE HOLE AND THUS 
R  INCORRECT OPERATION OF THE PROBE. 
R  (d) Move the vane of the AOA sensor 3FP1 to the top (nose-up) 
R  position. Keep the vane in this position with colored adhesive 
R  tape.
 4. Procedure_________
 Subtask 32-31-00-720-059 
R  A. Operational Check to Ensure Safety Valve Closes at 360 kts 
R  CAUTION : OBEY THESE PRECAUTIONS WHEN YOU DO THE TEST TO PREVENT DAMAGE_______ 
R  TO INSTRUMENTS: 
R  - PRESSURE SET MUST NOT BE MORE THAN 1050 hPa (31 in Hg) OR 
R  LESS THAN 115 hPa (3.39 in Hg) 
R  - CHANGES IN PRESSURE MUST NOT BE MORE THAN 6000 FEET/MINUTE 
R  - DO NOT SUDDENLY OPEN LINES TO AMBIENT AIR WHILE THE PRESSURE 
R  GENERATOR IS CONNECTED. 
R  CAUTION : THE TOTAL PRESSURE IN THE PITOT SYSTEM MUST NEVER BE LESS THAN_______ 
R  THE STATIC PRESSURE. THE DIFFERENCE BETWEEN THE PITOT AND THE 
R  STATIC PRESSURE CIRCUITS MUST NEVER BE MORE THAN 368 hPa (10.86 
R  in Hg).
 NOTE : For corrective action, do the necessary trouble-shooting____
 procedures (Ref. TSM 32 PB 101).

 1EFF : ALL 1 32-31-00Page 528 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. On the panel 20VU: - make sure that the ADIRS is set to the OFF position.
 2. Make sure that the travel range of the applicable MLG door is clear. 
R  3. Move the applicable ground door-operating handle to the OPEN position.
 4. Install the FALSE TARGET (98F32304000000) on the applicable proximity-sensor 21GA(20GA).
R R R R R R R R  5. Try to move the applicable ground door-operating handle to the CLOSE position. 
R
 6. On the panel 20VU: - set the IR 1 selector switch to ATT. 
R R R  7. Set the GROUND PRESSURE GENERATOR to give a signal of 268 to 270 kts.
R R R  8. Try to move the applicable ground door-operating handle to the CLOSE position. 

The MLG door opens.
The safety valve 49GA is de-energized(valve CLOSED).
The handle will not move.
NOTE : There can be unwanted movement
____ of the ground door-operating handle because of remaining green hydraulic pressure. If the handle can be moved more than five times, it is possible that the safety valve 49GA is defective.
The Air Data Inertial Reference Unit 1(ADIRU 1) energizes.
The handle will not move.
NOTE : There can be unwanted movement
____ of the ground door-operating handle because of remaining
 1EFF : ALL 1 32-31-00Page 529 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R R R R R
R 9. Slowly reduce the signal from the R GROUND PRESSURE GENERATOR to R between 255 and 265 kts.
 10. Make sure that the travel range of the applicable MLG door is clear.
R 11. Move the ground door-operating R handle to the CLOSE position.
R 12. Move the ground door-operating R handle to the OPEN position.
R 13. Set the GROUND PRESSURE R GENERATOR to OFF.
 14. On the panel 20VU:
 -set the IR 1 selector switch to OFF.
 Subtask 32-31-00-080-056
R B. Removal of the Test Equipment R green hydraulic pressure. If the handle can be moved more than five times, it is possible that the safety valve 49GA is defective.
The safety valve 49GA energizes (valve OPEN).
The MLG door closes.
The MLG door opens.
R (1) Disconnect and remove the ADAPTER COVER-STATIC PORT equipment from R the static probes 7DA1 and 8DA1.
R (2) Disconnect and remove the ADAPTOR-CHARGING,PITOT PROBE from the pitot R probe 9DA1.
R (3) Remove the colored adhesive tape from the pitot probe 9DA1 drain R holes and the AOA sensor 3FP1.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架4(64)