(c)
 Damping

 The end of stroke damping occurs in the two directions. The damping effect occurs when the piston head goes into the damping chamber, which causes the removed fluid to pass through the damping holes. On extension, the damping effect increases when one damping hole is closed by the piston.
 1EFF : ALL 1 32-31-00Page 59 1 1 May 01/05R 1 1 1CES 1

 H. NLG Door Actuating Cylinder (2531GM)
 (Ref. Fig. 030, 031)
 (1) Description
 The door actuator is a hydraulic actuator with rate control devices. The piston and piston rod are contained in a cylinder. The shape of the internal bore, the position of the return orifices, and the restrictor valve, control the damping.
 (a) Actuating Cylinder
 The NLG door actuating-cylinder is a two-acting type. A valve-housing on the body of the actuating-cylinder contains a check-valve. The movable part of the check-valve has a slot in the face that touches the valve seat.
 The actuating-cylinder connects:
 -
the door control-rod bellcrank at the piston-rod end

 -
the roof of the landing gear bay at the fixed end.

 (b) Restrictor
 An in-line restrictor (2536GM) is installed in the line to the
 annular side of the actuating cylinder. It controls the speed at
 which the piston-rod operates.
 The actuating cylinders range-of-travel is controlled by:

 -the NLG door uplock as the NLG doors close
 -an internal stop as the NLG doors open.
 (2) Operation
 (a) Doors Close
 With the NLG doors set to CLOSE, the pressurized hydraulic fluid goes into the annular side of the actuating-cylinder. The piston-rod retracts and closes the NLG doors. On the other side of the piston, the hydraulic fluid goes to return through the main return orifice and the slot in the closed check-valve. Near the end of the piston-rod travel, the piston closes the main return orifice. This causes a large decrease in the flow of fluid to return, which damps the end of the piston-rod travel.
 1EFF : ALL 1 32-31-00Page 60 1 1 May 01/05R 1 1 1CES 1

 NLG Door Actuating Cylinder (2531GM) Figure 030
 1EFF : 1 1R 1CES  ALL  1 11 1 32-31-00 Page 61 May 01/05

 NLG Door Actuating Cylinder - Schematic Figure 031
 1EFF : 1 1R 1CES  ALL  1 11 1 32-31-00 Page 62 May 01/05

 (b) Doors Open
 With the NLG doors set to OPEN, the aerodynamic loads help the doors to open. The restrictor (2536GM) decreases the return flow of fluid from the actuating-cylinder. This causes a damping-pressure on the annular side of the piston to control the speed at which the NLG doors open. The restrictor-valve (2535GM) keeps a limit on the damping-pressure. To do this, the valve decreases the flow of pressurized fluid to the extend side of the actuating-cylinder.
 J. MLG Uplock (2509GM,2510GM)
 (Ref. Fig. 032, 033)
 (1) Description
 The MLG uplock is a mechanical device that automatically locks the main gear in the retracted position. The uplock is closed mechanically and opened hydraulically in the normal extension and retraction mode. The uplock can also be opened mechanically in the free fall extension mode (Ref. 32-33-00). The primary components of the uplock are:
 -
a casing

 -
a hydraulic actuator

 -two proximity sensors with their related targets
 -
a locking mechanism

 -
a free-fall mechanical-release mechanism.

 (a) Casing
 The casing has two halves, which are connected by bolts. The hydraulic actuator has a piston, and is connected to the casing. A spring keeps the piston retracted when there is no hydraulic pressure. The actuator has two hydraulic ports A and B. The casing has two holes for rigging pins and are positioned for these functions: - one pin hole is for a rigging check of the position of the
 mechanism for the Free Fall Extension System - one pin hole locks the uplock in the closed position and is for a rigging check of the proximity sensors.
 1EFF : ALL 1 32-31-00Page 63 1 1 May 01/05R 1 1 1CES 1

 MLG Uplock (2509GM,2510GM) Figure 032
 1EFF : 1 1R 1CES  ALL  1 11 1 32-31-00 Page 64 May 01/05

 MLG Uplock - Schematic Figure 033
 1EFF : 1 1R 1CES  ALL  1 11 1 32-31-00 Page 65 May 01/05

 (b) Proximity Sensors
 The proximity sensors are attached to the casing and the targets to the latch assembly. They continuously supply an independent electrical signal to show the uplock configuration (uplock closed = 'target near' or uplock open = 'target far').
 The primary components of the locking mechanism are a latch assembly and a hook. The latch assembly has a bearing and two targets. The bearing turns on a pin at its center, as do the latch assembly and the hook. Tension springs connect the latch assembly to the hook. The hook has a cam which touches the bearing.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架4(41)