(2)
 Remove the warning notice(s).

 (3)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 32-22-15Page 406 1 1 Feb 01/04R 1 1 1CES 1

R  TASK 32-22-15-010-001 
R  Removal of the Leg Door Assy for Access 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR._______ 
R  WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY_______ 
R  OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM. 
R  1. Reason for the Job__________________ 
R  This procedure is only applicable when the leg door assy is removed for 
R  access. For the applicable procedure to remove the leg door assy for 
R  replacement, Ref. TASK 32-22-15-000-001. 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  safety barriers 
R  No specific  warning notice(s) 
R  B. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE  DESIGNATION 
R  -------------------------------------------------------------------------------
R  32-22-15-991-001  Fig. 401

 1EFF : ALL 1 32-22-15Page 407 1 1 Aug 01/99 1 1 1CES 1 1EFF : ALL 1 32-22-15Page 408 1 1 Aug 01/99 1 1 1CES 1 TASK 32-22-15-410-001

R  3. Job Set-up__________ 
R  Subtask 32-22-15-941-052 
R  A. Safety Precautions 
R  (1) In the cockpit, on the panel 400VU, put warning notice(s) in position 
R  to tell persons not to operate the landing gear control lever. 
R  (2) In the cockpit, on the steering handwheels (CAPT and F/O) and on the 
R  brake pedals, put warning notice(s) in position to tell persons not 
R  to operate them. 
R  (3) Put the safety barriers in position. 
R  4. Procedure_________ 
R  (Ref. Fig. 401/TASK 32-22-15-991-001) 
R  Subtask 32-22-15-020-051 
R  A. Removal of the Leg Door Assy 
R  NOTE : Do not change the adjustment of the rod (11), the rod end of the____ 
R  fitting (2) and the rod ends of the support (10). 
R  (1) Remove the nut (5) and the bolt (1) and disconnect the end fitting 
R  (2). 
R  (2) Remove the bushes (3) and (4), disconnect the rod (11). 
R  (3) Remove the nuts (7) and the bolts (9). 
R  (4) Remove the bushes (8) and disconnect the fairing (6) from the support 
R  (10). 
R  (5) Remove the fairing (6).

 Installation of the Leg Door Assy after Removal for Access
 1. Reason for the Job
__________________
 This procedure is only applicable when the leg door assy was removed for access. For the applicable procedure to install the leg door assy after replacement, Ref. TASK 32-22-15-400-001.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific  safety barriers
 No specific  warning notice(s)
R No specific  Torque Wrench : range 0.00 to 1.20 m.daN
R  (0.00 to 9.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. 04-004  USA MIL-PRF-23827 TYPE I
 SYNTH.ESTER BASED GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 Material No. 04-022  USA MIL-PRF-81322 GRADE 2
 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架4(20)