B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-005 Retracting the Slats on the Ground
27-80-00-991-008 Fig. 601
**ON A/C 001-049, 051-099, 101-149, 201-299,
27-80-00-991-010 Fig. 602 R **ON A/C 151-199, 301-399, 401-499,
27-80-00-991-010-A Fig. 602A
**ON A/C ALL
27-80-00-991-009 Fig. 603
3. Job Set-up
__________
Subtask 27-80-00-941-063
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in the cockpit to tell persons not to operate the slat controls.
(3) Put the adjustable access platform in position below the work area. Subtask 27-80-00-860-067
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the slats are fully retracted (Ref. TASK 27-80-00-866-005).
(2)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) is installed on the slat/flap control lever.
Subtask 27-80-00-865-071
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
4. Procedure
_________
(Ref. Fig. 601/TASK 27-80-00-991-008)
**ON A/C 001-049, 051-099, 101-149, 201-299,
(Ref. Fig. 602/TASK 27-80-00-991-010) R **ON A/C 151-199, 301-399, 401-499,
(Ref. Fig. 602A/TASK 27-80-00-991-010-A)
**ON A/C ALL
(Ref. Fig. 603/TASK 27-80-00-991-009)
**ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 27-80-00-220-051
A. Permitted Aerodynamic Tolerances between the Slats 1 thru 5
(1) Check the slat end step tolerances as follows:
(a) Measure and write down the slat end step dimensions at points 1, 2, 3 and 4 for the slats 1 thru 5 (28 dimensions in total).
Measurement Points for Permitted Tolerances between Slats
Figure 601/TASK 27-80-00-991-008
Slat End Step - Measurement Points
Figure 602/TASK 27-80-00-991-010
R 1EFF : 001-049, 051-099, 101-149, 201-299, 1 27-80-00Page 605 1 1 May 01/05 1 1 1CES 1
Slat End Step - Measurement Points
Figure 602A/TASK 27-80-00-991-010-A
R 1EFF : 151-199, 301-399, 401-499, 1 27-80-00Page 606 1 1 Aug 01/05 1 1 1CES 1
Slat Trailing Edge/Step - Measurement Points Figure 603/TASK 27-80-00-991-009
1EFF : 1 1R 1CES ALL 1 11 1 27-80-00 Page 607 Feb 01/00
(b) Compare the 28 dimensions:
-23 of the 28 dimensions measured must be between the general tolerance limits given in the table J
-3 of the 28 dimensions measured can be between the general tolerance limits given in the table J +/- 0.5 mm (0.0196 in.)
-2 of the 28 dimensions measured can be between the general tolerance limits given in the table J +/- 1.5 mm (0.0590 in.).
(2)
Check the slat upper-trailing edge to 'D' nose step tolerances as follows:
(a)
For the slat 1, measure and write down the dimension X at points A, B, C, D and E (5 dimensions).
(b)
For the slats 2 thru 5, measure and write down the dimension X at points B, C and D (12 dimensions).
(c)
Compare the 17 dimensions X:
-14 of the 17 dimensions X must be between +/- 0.5 mm (0.0196 in.) of each other
-3 of the 17 dimensions X can be between +/- 1.0 mm (0.0393 in.) of each other.
(3)
Check the slat lower-trailing edge to 'D' nose step tolerances as follows:
(a)
For the slat 1, measure and write down the dimension Y at points F, G, H, J and K (5 dimensions).
(b)
For the slats 2 thru 5, measure and write down the dimension Y at points F, G and H (12 dimensions).
(c)
Compare the 17 dimensions Y:
-11 of the 17 dimensions Y must be between +/- 1.0 mm (0.0393 in.) of each other
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱7(47)
