B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)
27-84-45-000-007 Removal of the Torque Shafts 6016CM(6066CM)/6020CM(6070CM)/6026CM(6076CM)/ 6030CM(6080CM)
27-84-44-991-001 Fig. 401 27-84-44-991-002 Fig. 402
3. Job Set-up
__________
(Ref. Fig. 401/TASK 27-84-44-991-001, 402/TASK 27-84-44-991-002)
Subtask 27-84-44-941-057
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice(s) in the cockpit to tell persons not to operate the slat controls.
(3)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) is on the slat/flap control lever.
Subtask 27-84-44-865-064
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
R 49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
Subtask 27-84-44-010-053
C. Get Access
(1)
Put an access platform in position below the applicable torque shaft.
(2)
Remove the applicable torque shaft (20) (Ref. TASK 27-84-45-000-007):
-
FOR 6017CM
remove the torque shaft FIN 6016CM
-
FOR 6019CM
remove the torque shaft FIN 6020CM
-
FOR 6067CM
remove the torque shaft FIN 6066CM
-
FOR 6069CM
remove the torque shaft FIN 6070CM.
(3)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) is on the applicable torque shaft (Ref. TASK 27-50-00-400-003).
Steady Bearings - Slat Power Transmission
Figure 402/TASK 27-84-44-991-002
1EFF : ALL 1 27-84-44 Page 412
1 1 Feb 01/98
1 1
1CES 1
4. Procedure
_________
(Ref. Fig. 402/TASK 27-84-44-991-002) Subtask 27-84-44-020-051
A. Removal of the Steady Bearing
(1) Remove the bolts (16), then remove the steady bearing (19) from the torque shaft (18) and the nose rib (17).
TASK 27-84-44-400-002
Installation of the Steady Bearings FIN 6017CM(6067CM)/6019CM(6069CM)
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-018 USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00)
Material No. 09-019 USA AMS 3267/3 LOW ADHESION CORROSION INHIBITING SEALANT (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱7(116)
