R C. Expendable Parts
R R R -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R R 8 8 patch patch 11-23-27 01 -020 11-23-27 01 -020A
R D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 27-80-00-866-004 51-75-12-300-003 27-80-00-991-001 Extending the Slats on the Ground Repair of Minor Paint Damage (Topcoat Only)Fig. 203
3. Job Set-up__________
Subtask 27-80-00-941-057
A. Safety Precautions
(1) Make sure that the warning notices are in position to tell persons not to operate the slat controls.
(2) Make sure that the safety barriers are in position.
Subtask 27-80-00-860-050
B. Aircraft Maintenance Configuration
(1) Make sure that the slats are fully extended (Ref. TASK 27-80-00-866-004).
(2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the slat/flap control lever on panel 114VU.
4. Procedure_________
(Ref. Fig. 203/TASK 27-80-00-991-001)
R R R R R R R R R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS_______ ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
Subtask 27-80-00-080-050
A. Removal of the Hoisting Sling
(1) Remove the trailing edge block (7) from the trailing edge of the slat.
(2) Remove the pip-pins (4) and disconnect the SLING-SLATS from the slat.
(3) Remove the lifting lugs (5) from the slat and connect them to the hoisting sling with the pip-pins (4).
(4) Remove the hoisting sling from the hoist.
(5) Install the blanking caps in the slat. Make sure that the top of the blanking caps are not above the surface of the slat.
R R R (6) Clean the area of the hoisting points with a lint-free cloth MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-003).
R (7) Install the new patch (8) on the hoisting points.
R R (8) If necessary, paint the patch (8) to the same color as the adjacent area (Ref. TASK 51-75-12-300-003).
5. Close-up
________ Subtask 27-80-00-942-056
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-80-00Page 236 1 1 Aug 01/05R 1 1 1CES 1
TASK 27-80-00-869-004
Reset of the Wing Tip Brake (WTB) of the Slat System on the Ground
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱7(44)
