(3)
Remove the input splined joint (8) from the bevel gearbox (1), as
follows:
(a)
Remove the pin (6) and the spring (7).
(b)
Remove the input splined joint (8) from the bevel gearbox (1).
(4)
Remove the bevel gearbox 6011CM (6061CM) (1) as follows:
(a)
Hold the bevel gearbox (1) so that it can not fall.
(b)
Remove the bolts (10) and the washers (9) which attach the bevel gearbox (1) to the support bracket.
(c)
Remove the bevel gearbox (1).
(5)
Remove the input splined joint (13) from the bevel gearbox 6009CM
(6059CM) (14).
(6)
Disconnect the torque shaft 6008CM (6058CM) (18) as follows:
(a)
Remove the nuts (4) and the bolts (3) which connect the torque shaft (18) to the input universal joint (17) of the bevel gearbox (14).
(b)
Disconnect the torque shaft (18) from the input universal joint (17).
(7)
Remove the input universal joint (17) from the bevel gearbox (14) as follows:
(a)
Remove the pin (6) and the spring (7).
(b)
Remove the input universal joint (17) from the bevel gearbox (14).
(8)
Hold the bevel gearbox (14) so that it can not fall.
(9)
Remove the bolts (10) and the washers (9) which attach the bevel
gearbox (14) to the support bracket.
63.5 Degree Bevel Gearbox
Figure 401/TASK 27-84-43-991-001
1EFF : ALL 1 27-84-43 Page 404
1 1 Feb 01/98
1 1
1CES 1
(10) Remove the bevel gearbox (14).
TASK 27-84-43-400-001
Installation of the Bevel Gearbox 63.5 6009CM,6011CM (6059CM,6061CM)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
NOTE : The installation procedure for the 63.5 degree bevel gearboxes
____ 6009CM/6011CM is specified. The procedure for the 63.5 degree bevel gearboxes 6059CM/6061CM is almost the same. If there are differences in the procedures they are specified.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 2.2 m (7 ft. 3 in.) R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 98D27504030001 1 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)
Material No. 05-005 USA MIL-C-16173 GRADE II
CORROSION PREVENTIVE (Ref. 20-31-00)
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A
CORROSION INHIBITING BRUSH CONSISTENCY
(Ref. 20-31-00)
Material No. 09-019 USA AMS 3267/3
LOW ADHESION CORROSION INHIBITING SEALANT
(Ref. 20-31-00)
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
Material No. 16-003 F ASNB70720
COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
20-28-00-912-002 Electrical Bonding of Components With Conductive Bolts and Screws in the Tanks 20-28-00-912-004 Electrical Bonding of Components With Conductive
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱7(110)
