3. Job Set-up
__________
Subtask 27-84-43-860-052
A. Aircraft Maintenance Configuration
(1)
Make sure that the slats are in the 0 degree position (Ref. TASK 27-80-00-866-005).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed (Ref. TASK 27-00-00-480-002) on the slat/flap control lever.
(3)
Make sure that the access platform is in position at the opening of the main door of the main gear.
(4)
Make sure that the Green and Blue hydraulic systems are depressurized and put them in the maintenance configuration (Ref. TASK 29-00-00-864-001).
(5)
Make sure that the warning notice in position to tell persons not to pressurize the hydraulic systems.
(6)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) is installed to lock the left slat transmission.
(7)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) is installed to lock the right slat transmission.
Subtask 27-84-43-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________
(Ref. Fig. 401/TASK 27-84-43-991-001)
NOTE : The gearbox is a unit filled with grease and is not a hermetically
____ sealed unit. It is normal for this grease to have some oil separation. The external surface of the gearbox may be moist with this separated oil as it is not a sealed unit. However, any separated oil in the unit that touches the grease will be changed back during operation. The oil separation will decrease during in-service operation until the lubricant is in a condition that is stable. This is normal and will not cause damage to the unit.
Subtask 27-84-43-910-051
A. Preparation for Installation
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
To install the same gearbox, clean the splined surfaces of the connections with CLEANING AGENTS (Material No. 11-002).
(2)
Apply SEALANTS (Material No. 09-019) to the face of the bevel gearbox 6009CM (6059CM) (14) which touches the support bracket.
Subtask 27-84-43-420-051
B. Installation of the Bevel Gearbox
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Put the bevel gearbox (14) in position on the support bracket.
(4)
Attach the bevel gearbox (14) to the support bracket with the bolts
(10) and the washers (9).
(5)
TORQUE the bolts (10) to between 0.78 and 0.96 m.daN (69.02 and 84.95
lbf.in)
(6)
At the bonding point continue as follows (Ref. TASK 20-28-00-912-004):
(a)
Seal the bolt (10) with SEALANTS (Material No. 09-013).
(b)
Apply STRUCTURE PAINTS (Material No. 16-003) (dyed blue) to the bonding point.
(7)
Apply SPECIAL MATERIALS (Material No. 05-005) to the heads of the
bolts (10).
(8)
Apply COMMON GREASE (Material No. 04-018) to the splines of the input universal joint (17).
(9)
Install the input universal joint (17) as follows:
(a)
Engage the input universal joint (17) of the bevel gearbox (14) in the bevel gearbox input.
(b) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱7(111)
