4. Procedure
_________
(Ref. Fig. 401/TASK 27-64-51-991-006)
**ON A/C 001-003, 051-052,
(Ref. Fig. 402/TASK 27-64-51-991-007) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 402A/TASK 27-64-51-991-007-A)
**ON A/C ALL
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
**ON A/C 001-003, 051-052,
Subtask 27-64-51-560-050-A
A. Preparation for a Replacement Component
(1)
Push the piston rod into the body of the servo-control until it touches the internal limit.
(2)
Measure the dimension X. Dimension X must be between 220.0 mm (8.6614 in.) and 223.0 mm (8.7795 in.).
(3)
If the spoiler is safetied with STA-LOK nuts, do the steps that follow:
(a) To adjust the piston rod to get the dimension X: 1 Remove and discard the lockwire from the locknut (70).
_
2 Loosen the locknut (70).
_
3 Turn the eye-end (63) in the applicable direction.
_
4 Make sure that the serrated washers (62) and (69) are engaged
_
correctly.
(4)
When the dimension X is correct, TORQUE the locknut (70) to between
3.0 and 8.0 m.daN (22.12 and 58.99 lbf.ft).
(5)
Safety the locknut (70) with MISCELLANEOUS (Material No. 19-010).
(6)
If the spoiler is safetied with ABS 0738 nuts, do the steps that follow:
(a) To adjust the piston rod to get the dimension X: 1 Remove and discard the lockwire from the locknut (72).
_
2 Loosen the locknut (72).
_
3 Turn the eye-end (63) in the applicable direction.
_
4 Make sure that the serrated washers (62) and (71) are engaged
_
correctly.
(7) When the dimension X is correct, TORQUE the locknut (72) to between
3.0 and 8.0 m.daN (22.12 and 58.99 lbf.ft).
(8) Safety the locknut (72) with MISCELLANEOUS (Material No. 19-010). R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 27-64-51-560-050
A. Preparation for a Replacement Component
(1)
Push the piston rod into the body of the servo-control until it touches the internal limit.
(2)
Measure the dimension X. Dimension X must be between 220.0 mm (8.6614 in.) and 223.0 mm (8.7795 in.).
(3)
To adjust the piston rod to get the dimension X:
(a)
Remove and discard the lockwire from the locknut (72).
(b)
Loosen the locknut (72).
(c)
Turn the eye-end (63) in the applicable direction.
(d)
Make sure that the serrated washers (62) and (71) are engaged correctly.
(4)
When the dimension X is correct, TORQUE the locknut (72) to between
3.0 and 8.0 m.daN (22.12 and 58.99 lbf.ft).
(5) Safety the locknut (72) with MISCELLANEOUS (Material No. 19-010). **ON A/C ALL
Subtask 27-64-51-420-060
B. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area with MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Make sure that the hydraulic line end-fittings are serviceable.
(5)
Extend, by hand, the piston rod of the spoiler servo-control.
(6)
Install the COLLAR-SAFETY, SPOILER (98D27604000000) on the piston rod of the spoiler servo-control.
R **ON A/C 001-003, 051-052,
Subtask 27-64-51-420-053-A
C. Installation of the Spoiler Servo-Control CAUTION : SUPPORT THE SERVO CONTROL 7.5kg (16.5lb) AND THE SPOILER
_______ APPROXIMATELY 15kg (33lb). THIS WILL PREVENT DAMAGE TO:
-
THE HYDRAULIC LINES
-
THE ELECTRICAL CABLES
-
THE STRUCTURE.
(1)
Apply a layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the interface of the servo-control and under the heads of the bolts (61).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱7(22)
