R  NOTE : The necessary viscosity is 17-23 seconds, 4 mm (0.16 in.)____ 
R  DIN cup. 
R  (b) Permit the mixture 15 minutes reaction time before use. 
R  NOTE : Pot life is 8 hours maximum.____ 
R  It will be necessary to add STRUCTURE PAINTS (Material No. 
R  16-047) (thinner 62) after approx. 4 hours to keep the 
R  necessary viscosity. 
R  NOTE : Conditions for use:____ 
R  - Temperature between 15 DEG.C (59.00 DEG.F) and 30 DEG.C 
R  (86.00 DEG.F), 
R  - Relative humidity 35-75% . 
R  (c) For a textured finish apply the mixture in 1-4 cross coats with a 
R  GUN - AIR SPRAY, STANDARD PAINT and a NOZZLE DIA 1.5 MM (1/16 
R  IN). 
R  NOTE : The necessary coat thickness of a textured finish is____ 
R  between 0.03 mm (0.0011 in.) and 0.09 mm (0.0035 in.). 
R  NOTE : The textured finish is:____ 
R  - Dust dry after 20 minutes, 
R  - Transport dry after 8 hours, 
R  - Fully dry after 7 days at room temperature. 
R  Over-painting: Between 20 minutes and 12 hours. 
R  NOTE : If the drying time between the coats is more than 12____ 
R  hours: 
R  - clean the repair with STRUCTURE PAINTS (Material No. 16-
R  047) (thinner 62) and a lint-free cotton cloth 
R  MISCELLANEOUS (Material No. 19-003). 
R  - Rub it with emery cloth, 320-400 grade 
R  and 
R  - Clean it with CLEANING AGENTS (Material No. 11-010) and 
R  a lint-free cotton cloth MISCELLANEOUS (Material No. 19-
R  003). 
R  NOTE : To make the cure faster you can add heat 60 DEG.C (140.00____ 
R  DEG.F) to the repair area. 
R  The textured finish is then: 
R  - Transport dry after 40 minutes, 
R  - Fully dry after 12 hours. 
R  Over-painting: Heat-cured for 20 minutes maximum if you 
R  do not clean or rub the repair.

 EFF : ALL

25-00-00Page 879

R  (7) Remove the masking tape and the masking paper from the adjacent 
R  components or areas. 
R  Subtask 25-00-00-370-054 
R  C. Repair of the Paint Coating of Thermoplastic Components and Aluminum 
R  Parts in the Cabin 
R  WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE_______ 
R  MATERIAL/S. 
R  USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK. 
R  WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK_______ 
R  AREA WHEN YOU USE SPECIAL MATERIALS. 
R  IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH 
R  OR IN YOUR EYES : 
R  -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 
R  MINUTES. 
R  -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. 
R  DO NOT BREATHE THE FUMES FROM THE MATERIAL. 
R  DO NOT SMOKE WHEN YOU USE THE MATERIAL. 
R  DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF 
R  HEAT. 
R  THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE 
R  AND SKIN IRRITANTS. 
R  NOTE : The procedure that follows agrees with the (Ref. FAR 25.853(a-1))____ 
R  (Fire resistant repairs to the passenger compartment). 
R  NOTE : The procedure is approved for repair of surfaces smaller than 24____ 
R  in.2 (154.83 cm2). 
R  NOTE : The procedure is approved for repair of surfaces larger than 24____ 
R  in.2 (154.83 cm2) , but only for parts of the component. 
R  (1) Clean the component with CLEANING AGENTS (Material No. 11-010) and a 
R  lint-free cotton cloth MISCELLANEOUS (Material No. 19-003). 
R  (2) Apply masking paper and BONDING AND ADHESIVE COMPOUNDS (Material No. 
R  08-074) o the adjacent components and areas. 
R  (3) Make the repair area smooth with emery cloth, 320-400 grade. 
R  (4) Clean the repair area with CLEANING AGENTS (Material No. 11-010) and 
R  a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).

 EFF : ALL

25-00-00Page 880
Aug 01/05

R  (5) Prepare a mixture for a textured finish. 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備1(64)