(3)
Make sure that the seat is not loose and that the fittings are in the correct condition.
(4)
Make sure that the holes for the bolts are in the correct condition and have no corrosion.
(5)
Make sure that the seat belt and the buckle are in the correct condition.
(6)
Make sure that the seat assembly is not loose.
(7)
Make sure that the nuts that attach the seat to the partition are in the correct position and have no corrosion.
(8)
Make sure that clearance is correct at the control levers.
(9)
Make sure that the sideways movement is correct.
(10)
Make sure that the headrest operation is correct.
(11)
Make sure that the operation of the locking/unlocking system is correct.
EFF : ALL
25-11-41Page 601
(12) Make sure that the retaining pins are not damaged.
EFF : ALL
25-11-41Page 602
SEAT - FOURTH OCCUPANT (13MM) - REMOVAL/INSTALLATION
____________________________________________________
TASK 25-11-42-000-001
Removal of the Fourth Occupant Seat (13MM)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-11-42-991-001 Fig. 401
3. Procedure
_________ (Ref. Fig. 401/TASK 25-11-42-991-001) Subtask 25-11-42-020-050
A. Removal of the Fourth Occupant Seat (13MM)
(1)
Removal of the seat (10).
(a)
Hold the seat (10), loosen the two screws (11).
(b)
Turn the seat (10) so that you can release the rollers (15) from their guides, remove the seat (10).
(2)
Removal of the back
(a)
Remove the cover (7) attached with velcro tapes.
(b)
Loosen the screws (9), remove the back frame (8).
(3)
Removal of the headrest
(a)
Remove the cover (1) attached with velcro tapes.
(b)
loosen the screws (3), remove the headrest frame (2).
EFF : ALL
25-11-42Page 401
Fourth Occupant Seat
Figure 401/TASK 25-11-42-991-001- 12 (SHEET 1)
EFF : ALL 25-11-42 Page 402
Feb 01/98
CES
Fourth Occupant Seat
Figure 401/TASK 25-11-42-991-001- 22 (SHEET 2)
EFF : ALL 25-11-42 Page 403
Feb 01/98
CES
(4) Removal of the safety belt
(a)
Remove the two circlips (13), remove the two pins (14), remove the safety belt (12).
(b)
When you have removed the headrest, loosen the screws (4), disconnect the cable (5) and remove the reel (6).
EFF : ALL
25-11-42Page 404
TASK 25-11-42-400-001
Installation of the Fourth Occupant Seat (13MM)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-11-42-991-001 Fig. 401
3. Procedure
_________ (Ref. Fig. 401/TASK 25-11-42-991-001) Subtask 25-11-42-420-050
A. Installation of the Fourth Occupant Seat (13MM)
(1)
Installation of the seat (10).
(a)
Install the seat (10) so that you can engage the rollers (15) in their guides.
(b)
Install the screws (11) and tighten them.
(2)
Installation of the back frame and cover
(a)
Install the back frame (8), install the screws (9) and tighten them.
(b)
Install the cover (7) and push it to get correct attachment of the velcro tapes.
(3)
Installation of the safety harness
(a) Install the reel (6), install the screws (4) and tighten them. Connect the cable (5).
EFF : ALL
25-11-42Page 405
(b) Install the safety belt (12), install the two pins (14) and the circlips (13).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備1(102)
