25-00-00Page 808
May 01/05
R
CES 3. Job Set-up
__________
Subtask 25-00-00-861-066
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
Subtask 25-00-00-020-064
B. If necessary, remove the component you will repair from the aircraft (refer to the related AMM chapter).
4. Procedure
_________
Subtask 25-00-00-350-064
A. Do the Repair
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1)
Increase the temperature at the edge of the decor foil with an adjustable HOT AIR BLOWER MAX OPERATING 370 DEG C (700 DEG F) to max 100 deg.C (212.00 deg.F)
(2)
Lift the edge of the decor foil.
(3)
Pull the decor foil from the component in approximately 150 mm (5.9 in.) wide strips while the max 100 deg.C (212.00 deg.F) hot air is applied.
(4)
Remove the unwanted adhesive with a emery cloth, 320-400 grade.
EFF : ALL
25-00-00Page 809
May 01/05
R
CES
(5)
Clean the repair area with CLEANING AGENTS (Material No. 11-010) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) .
(6)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-006B) or BONDING AND ADHESIVE COMPOUNDS (Material No. 08-011A) to the repair area.
(7)
Install the SPECIAL MATERIALS (Material No. 05-084)
(a)
Cut the new decorative foil to the correct dimension.
(b)
Remove the protective layer from the decorative foil.
(c)
Carefully put the decorative foil on the repair area.
(d)
Use a ROLLER - RUBBER, SOFT to push the decorative foil on to the repair area.
Subtask 25-00-00-420-064
B. Installation of the removed Component
(1) If you have removed the component to do the repair, install the component in the aircraft (refer to the related AMM chapter).
5. Close-up
________ Subtask 25-00-00-942-071
A. Close-up
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 25-00-00-862-067
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
EFF : ALL
25-00-00Page 810
May 01/05
R
CES EFF : ALL
TASK 25-00-00-340-002
Repairs to Polycarbonate (PC) Sheet Components
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R No specific No specific 1 CUTTER - THIN BLADE 1 PLATE - BASE, RUBBER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備1(47)
