25-13-14Page 403

 TASK 25-13-14-000-002 Removal of the Sliding Table
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-13-14-991-002 Fig. 402
 3. Procedure
_________
 (Ref. Fig. 402/TASK 25-13-14-991-002) Subtask 25-13-14-020-051
 A. Removal of the Sliding Table
 (1)
 Pull the table. Do not remove it fully from its housing.

 (2)
 Remove the screws (8).

 (3)
 Remove the sliding table (7).

 EFF : ALL

25-13-14Page 404

 Sliding Table.
 Figure 402/TASK 25-13-14-991-002
 EFF :  ALL  25-13-14 Page 405 
Feb 01/98
 CES 

 TASK 25-13-14-400-002 Installation of the Sliding Table
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
25-13-14-991-002 Fig. 402
 3. Procedure
_________ (Ref. Fig. 402/TASK 25-13-14-991-002) Subtask 25-13-14-420-051
 A. Installation of the Sliding Table
 (1)
 Remove the arm (9).

 (2)
 Install the sliding table.

 (3)
 Install the screws (8) and tighten them.

 4. Close up
________ Subtask 25-13-14-942-051
 A. Make sure that the work area is clean and clear of tools and other items.
 EFF : ALL

25-13-14Page 406

 TASK 25-13-14-000-003
 Removal of the Actuator on the Foot Rest Assembly

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 25-13-14-000-001 Removal of the Foot Rest and Sliding Table Assembly
R  **ON A/C 001-049, 051-061, 101-103, 201-203,
 25-13-14-991-003 Fig. 403
 **ON A/C ALL

R  Post SB 25-1225 For A/C 001-049,051-061,101-103,201-203, 25-13-14-991-003-A Fig. 403A **ON A/C ALL
 3. Job Set-up
__________
 Subtask 25-13-14-861-051

 A. Aircraft Maintenance Configuration
 (1) Energize the ground service network
 (Ref. TASK 24-42-00-861-001)

 EFF : ALL

25-13-14Page 407

 4. Procedure
_________ R **ON A/C 001-049, 051-061, 101-103, 201-203,
 (Ref. Fig. 403/TASK 25-13-14-991-003) **ON A/C ALL R Post SB 25-1225 For A/C 001-049,051-061,101-103,201-203, (Ref. Fig. 403A/TASK 25-13-14-991-003-A) **ON A/C ALL
 Subtask 25-13-14-020-052
 A. Removal of the Foot Rest and Sliding Table Assembly (Ref. TASK 25-13-14-000-001)
R **ON A/C 001-049, 051-061, 101-103, 201-203,
 Subtask 25-13-14-020-053
 B. Removal of the Actuator on the Foot Rest Assembly
 (1)
 Put the foot rest assembly (5) on a bench, with the foot rest on the top and in the stowed position.

 (2)
 Remove the retaining ring (1) (on the actuator rod side) and discard it.

 (3)
 Lightly compress the actuator (3) and disengage the actuator rod from its pin (2).

 (4)
 Remove only one retaining ring (1) (on actuator body side) and discard it.

 (5)
 Disengage the lateral pin (4).

 (6)
 Remove the actuator.

 EFF : ALL

25-13-14Page 408

 Actuator on the Foot Rest and Sliding Table Assembly Figure 403/TASK 25-13-14-991-003 
R  EFF :  001-049, 051-061, 101-103, 201-203,  25-13-14 Page 409 May 01/05
 CES 

 Actuator on the Foot Rest and Sliding Table Assembly Figure 403A/TASK 25-13-14-991-003-A 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備1(122)