(2.00 to 20.00 m.daN) R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN)
 No specific Torque Wrench : range 180.00 to 1800.00 lbf.in
 (2.00 to 20.00 m.daN)
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
12-13-24-612-041 IDG Servicing - Filling of the IDG with Oil or
 Addition of Oil after a level Check
 71-00-00-710-001 Dry Motoring Check
 71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors
 24-21-49-991-300 Fig. 401 3. Job Set-up

__________
 Subtask 24-21-49-860-050
 A. Aircraft Maintenance Configuration.
 (1)
 Make sure that the warning notice(s) is (are) on the panel 115VU to tell persons not to start the engine 1(2).

 (2)
 Make sure that the warning notice(s) is (are) on the panel 50VU to tell persons not to power supply the FADEC system.

 Subtask 24-21-49-865-051
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 1000EM1, 4000XU
 122VU ELEC/GCU/1 2XU1 T26 122VU ELEC/IDG1/DISC 1XT T24
 FOR 1000EM2, 4000XU 122VU ELEC/GCU/2 2XU2 T27 122VU ELEC/IDG2/DISC 2XT T25
 Subtask 24-21-49-010-052
 C. Get Access
 (1) Make sure that the fan cowl doors are open (Ref. TASK 71-13-00-010-040).
 -
FOR 1000EM1
 437AL, 438AR

 -
FOR 1000EM2
 447AL, 448AR

 4. Procedure
_________ (Ref. Fig. 401/TASK 24-21-49-991-300) Subtask 24-21-49-420-050
 A. Installation of the upper oil-in tube assembly CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
 (1)
 Remove the protective covers from the hose, tubes, and fittings on the IDG and the IDG oil cooler.

 (2)
 Connect the upper oil-in tube (10) to the fitting on the IDG oil cooler.

 (3)
 TORQUE the coupling nut on the upper oil-in tube (10) to between 1000 and 1050 lbf.in (11.30 and 11.86 m.daN).

 NOTE : Use a second wrench to hold the fitting on the IDG oil cooler
____ when you torque the tube (10) coupling nut.
 (4)
 Put the clampshell (25) on the tube (10) and attach it to the channel with the screw (15).

 (5)
 TORQUE the screw (15) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).

 Subtask 24-21-49-420-051
 B. Installation of the lower oil-in tube assembly CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
 (1)
 Loosely connect the lower oil-in tube (45) to the upper oil-in tube (10). Do not torque the tube coupling nut at this time.

 (2)
 Put the clampshell (25) on the tube (45) and attach it to the channel with the the screw (15), washer (30), and nut (35).

 (3)
 Put the clampshells (25) on the tube (45) and attach them to the brackets at Sta. 158 (B1) with the screws (15). (two locations).

 (4)
 TORQUE the screw (15) and nut (35) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).

 (5)
 TORQUE the coupling nut on the lower oil-in tube (45) to between 1000 and 1050 lbf.in (11.30 and 11.86 m.daN).

 NOTE : Use a second wrench to hold the fitting on the tube (10) when
____ you torque the tube (45) coupling nut.
 Subtask 24-21-49-420-052
 C. Installation of the oil-in hose assembly CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
 (1)
 Connect the oil-in hose (55) to the lower oil-in tube (45).

 (2)
 TORQUE the coupling nut on the oil-in hose (55) to between 1000 and 1050 lbf.in (11.30 and 11.86 m.daN).

 NOTE : Use a second wrench to hold the fitting on the tube (45) when
____ you torque the hose (55) coupling nut.
 (3) Connect the oil-in hose (55) to the union on the IDG (60). R (4) TORQUE the coupling nut on the oil-in hose (55) to between 75 and
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源1(76)