1EFF : 401-499, 1 24-21-00Page 25 1 1 Aug 01/05 1 1 1CES 1

 IDG 1 Oil Low Pressure - Upper and Lower ECAM Display Unit R Figure 009 (SHEET 1)
 1EFF : ALL 1 24-21-00Page 26 1 1 Aug 01/05 1 1 1CES 1

 IDG 1 Oil Low Pressure - Upper and Lower ECAM Display Unit R Figure 009 (SHEET 2)
 1EFF : ALL 1 24-21-00Page 27 1 1 Aug 01/05 1 1 1CES 1

 IDG 1 Oil Overheat - Upper and Lower ECAM Display Unit R Figure 010 (SHEET 1)
 1EFF : ALL 1 24-21-00Page 28 1 1 Aug 01/05 1 1 1CES 1

 IDG 1 Oil Overheat - Upper and Lower ECAM Display Unit R Figure 010 (SHEET 2)
 1EFF : ALL 1 24-21-00Page 29 1 1 Aug 01/05 1 1 1CES 1

 IDG 1 Oil Overheat Advisory - Upper and Lower ECAM Display Unit R Figure 011 (SHEET 1)
 1EFF : ALL 1 24-21-00Page 30 1 1 Aug 01/05 1 1 1CES 1

 IDG 1 Oil Overheat Advisory - Upper and Lower ECAM Display Unit R Figure 011 (SHEET 2)
 1EFF : ALL 1 24-21-00Page 31 1 1 Aug 01/05 1 1 1CES 1

R  IDG 1 Disconnect - Lower ECAM Display Unit Figure 012
 1EFF : 1 1 1CES  ALL  1 111 24-21-00 Page 32 Aug 01/05

 In this case, the IDG must be disconnected manually. For this, the PUSH-TO-DISC IDG1(2) safety-guarded pushbutton switch, installed on the panel 35VU, must be pushed.
 NOTE : - IDG disconnection is irreversible in flight. Connection of the
____ system is then possible only on the ground with engines shut down.
 -Illumination of IDG FAULT legend is inhibited at engine shut
 down (under speed) in particular.
 In case of overheat or oil pressure drop, the legend goes off
 because a disconnection occurs (speed below 2000 rpm).

 -The IDG must not operate for more than 50 hours in the disconnected mode. If the IDG operates for more than 50 hours in the disconnected mode, it will be necessary to replace it and send the removed IDG for a shop inspection. This is because there is a risk of damage to the ball bearing assembly on the input shaft.
 C. Reconnection of the IDG A mechanical reset handle is fitted to the IDG. The handle is used to reconnect the drive while the engine is stationary on the ground.
 D. Oil filter A clogged filter indication is provided by a local visual pop out indicator. The indicator is installed opposite the drive end of the IDG.

 INTEGRATED DRIVE GENERATOR SYSTEM (IDG, GCU) - SERVICING
________________________________________________________ TASK 24-21-00-920-040 R Drain IDG Oil System, Discard Filter Element(s) and Replenish WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
 WARNING : WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES.
_______
 HOT OIL CAN BURN YOUR EYES AND SKIN.
 IF OIL TOUCHES YOUR EYES OR SKIN, GET MEDICAL AID.

 CAUTION : USE ONLY NEW CANS OF OIL WHEN YOU FILL THE IDG WITH OIL OR ADD OIL TO
_______
 THE IDG.
 THE CONTAMINATION IN OIL THAT STAYS IN OPEN CANS CAN CAUSE FAST
 DETERIORATION OF THE OIL AND WILL DECREASE THE LIFE OF THE IDG.

 CAUTION : DO NOT USE SOLVENTS THAT CONTAIN CHLORINE TO CLEAN THE EQUIPMENT
_______ (PUMP, HOSES, TANK AND FUNNEL) USED TO FILL THE IDG WITH OIL. CHLORINE CONTAMINATION OF THE OIL CAN CAUSE FAST DETERIORATION OF THE OIL AND WILL DECREASE THE LIFE OF THE IDG.
 CAUTION : DO NOT OPERATE THE IDG:
_______
 -
IF IT CONTAINS TOO MUCH OIL

 -
IF IT DOES NOT CONTAIN ENOUGH OIL
 IF YOU DO, YOU CAN CAUSE DAMAGE TO THE IDG.

 CAUTION : DO NOT DO THE SERVICING OF A DISCONNECTED IDG. CONTINUED OPERATION OF
_______
 A DEFECTIVE IDG CAN CAUSE DAMAGE.

 1. Reason for the Job
__________________
 Refer to the MPD TASK: 242100-03 To drain the IDG, replace the IDG oil filter element(s) and fill the IDG with oil.

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 5.7 l (1.5 USgal)
 No specific warning notice
 No specific Torque Wrench : range 2.00 to 26.00 lbf.ft

 (0.20 to 3.60 m.daN)
 No specific Torque Wrench : range 36.00 to 220.00 lbf.in

 (0.40 to 2.60 m.daN)
 DH13PM 1 TANK - ENGINE OIL FILLING UP

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源1(47)