(a) Put a warning notice in position to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
On the overhead maintenance panel 50VU:
(a)
Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b)
Put a warning notice in position to tell persons not to energize the FADEC 1(2).
Subtask 24-21-00-010-053
B. Open the right fan cowl door (Ref. TASK 71-13-00-010-040):
-
FOR 1000EM1
438AR
-
FOR 1000EM2
448AR
1EFF : ALL 1 24-21-00Page 615 1 1 Aug 01/05R 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 602/TASK 24-21-00-991-907)
Subtask 24-21-00-020-057
A. Removal of the Lockwire
WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE. CUT,
_______ REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(1) Cut and remove the lockwire (1) from the tension bolt (2).
Subtask 24-21-00-640-051
B. Lubrication of the QAD Adapter and the Tension Bolt
(1)
Apply SPECIAL MATERIALS (Material No. 05-027) with a spray to the QAD ring (3), the mating surface between the QAD adapter and the QAD ring,in the zone where you can get access.
(2)
Lubricate the tension bolt (2) with the OILS (Material No. 03-002).
Subtask 24-21-00-220-050
C. Torque Check of the QAD Adapter Tension-Bolt
(Ref. Fig. 603/TASK 24-21-00-991-908)
(1)
Measure the torque value on the tension bolt (2) If the torque on the tension bolt (2) of the QAD adapter is less than 15 lbf.ft (2.03 m.daN), adjust the QAD ring (3). To do this, tap the edge of the QAD ring (3) that you can see with a brass drift to make sure that the torque values you measure are correct. TORQUE the tension bolt (2) to between 265 and 305 lbf.in (2.99 and 3.44 m.daN).
(2)
Shake the antidrive end of the IDG to do a check of the QAD adapter. If the IDG is loose, remove the IDG mounting flange (Ref. TASK 24-21-51-000-040) and the QAD adapter (Ref. TASK 24-21-41-000-040). Tap the edge of the QAD ring (3) again and do the torque check again until the torque value does not decrease by more than 24 lbf.in (0.27 m.daN).
(3)
Do a check of the distance between the ring lug and the bracket of the QAD ring. If the distance is less than 0.56 in. (14.3 mm) minimum, replace the IDG (Ref. TASK 24-21-51-000-040) and the QAD adapter (Ref. TASK 24-21-41-000-040).
1EFF : ALL 1 24-21-00Page 616 1 1 Aug 01/05R 1 1 1CES 1
IDG System - QAD Adapter Figure 602/TASK 24-21-00-991-907
1EFF : 1 1R 1CES ALL 1 11 1 24-21-00 Page 617 Aug 01/05
IDG System - QAD Adapter Wear Allowance Figure 603/TASK 24-21-00-991-908
1EFF : 1 1R 1CES ALL 1 11 1 24-21-00 Page 618 Aug 01/05
Subtask 24-21-00-420-056
D. Safety the tension bolt (2) with lockwire (1).
5. Close-up
________ Subtask 24-21-00-410-053
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the right fan cowl door (Ref. TASK 71-13-00-410-040):
-
FOR 1000EM1
438AR
-
FOR 1000EM2
448AR
(3)
Remove the warning notice(s).
1EFF : ALL 1 24-21-00Page 619 1 1 Aug 01/05R 1 1 1CES 1
R **ON A/C 401-499,
R TASK 24-21-00-210-043- 01
R Torque Check of the Quick Attach-Detach (QAD) Adapter Tension-Bolt (P/N 772896)
R WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER_______
R THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO
R ONE HOUR.
R 1. Reason for the Job__________________
R Refer to the MPD TASK: 242100-01
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM ELECTRICAL POWER 電源1(66)
