曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  pin hole of the QAD gasket. 
R  NOTE : Make sure that the stripe of the QAD ring is aligned with the____ 
R  stripe on the adapter plate. 
R  (3) Install the QAD adapter (2) on the accessory-gearbox mounting-pad 
R  with the screws (3). 
R  NOTE : Make sure that the words "TOP CFM" on the QAD adapter are in____ 
R  the top position (12 o'clock). 
R  (4) Use a brush to apply a thin layer of SPECIAL MATERIALS (Material No. 
R  05-063) of the conical surface of the heads of the screws (3) and the 
R  threads of the screws.

 

R  (5) TORQUE the screws (3) to between 348 and 384 lbf.in (3.93 and 4.33 
R  m.daN). 
R  Subtask 24-21-41-420-059 
R  D. Install the IDG (Ref. TASK 24-21-51-400-040). 
R  5. Close-up________ 
R  Subtask 24-21-41-410-056 
R  A. Close Access 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Close the fan cowl doors (Ref. TASK 71-13-00-410-040): 
R  - FOR 1000EM1 
R  437AL, 438AR 
R  - FOR 1000EM2 
R  447AL, 448AR 
R  (3) Remove the warning notice(s).

 

 TUBING - IDG COOLER OIL - REMOVAL/INSTALLATION
______________________________________________ TASK 24-21-49-000-003 Removal of the IDG Cooling Oil-in Tubes and Hoses WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
 WARNING : WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES.
_______ HOT OIL CAN BURN YOUR EYES AND SKIN. IF OIL TOUCHES YOUR EYES OR SKIN, GET MEDICAL AID.
 WARNING : DO NOT GET ENGINE OIL ON YOUR SKIN FOR A LONG TIME. FLUSH THE OIL
_______ FROM YOUR SKIN WITH WATER. THE OIL IS POISONOUS AND CAN GO THROUGH YOUR SKIN AND IN TO YOUR BODY.
 CAUTION : DO NOT LET ENGINE FUEL OR OIL FALL ON THE ENGINE. UNWANTED FUEL OR
_______ OIL MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FUEL OR OIL CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific protective covers
 No specific warning notice(s)
 No specific container 1 USgal (3.7854 l)
 DH13PM 1 TANK - ENGINE OIL FILLING UP

 

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 24-21-49-991-300 Fig. 401
 3. Job Set-up
__________
 Subtask 24-21-49-941-050
 A. Safety Precautions
 (1)
 Make sure that the engine 1(2) shutdown occured not less than 5 minutes before you do this procedure.

 (2)
 On the panel 115VU:

 (a) Put a warning notice(s) to tell persons not to start the engine 1(2).

 (3)
 On the panel 50VU:

 (a)
 Make sure that the ON legend of the ENG/FADEC GND PWR 1(2) pushbutton switch is off.

 (b)
 Put a warning notice(s) to tell persons not to power supply the FADEC system.

 

 Subtask 24-21-49-865-050
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 1000EM1, 4000XU
 122VU ELEC/GCU/1 2XU1 T26
 122VU ELEC/IDG1/DISC 1XT T24 FOR 1000EM2, 4000XU
 122VU ELEC/GCU/2 2XU2 T27
 122VU ELEC/IDG2/DISC 2XT T25

 Subtask 24-21-49-010-050

 C. Get Access
 (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
 -
FOR 1000EM1
 437AL, 438AR

 -
FOR 1000EM2
 447AL, 448AR

 

 4. Procedure
_________ (Ref. Fig. 401/TASK 24-21-49-991-300) Subtask 24-21-49-864-050
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源1(74)