Servicing of the IDG afer Oil Contamination / DPI Popped
Figure 303/TASK 24-21-00-991-303
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 24-21-00Page 332 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1R Servicing of the IDG after Oil Contamination / DPI Popped R Figure 303A/TASK 24-21-00-991-303-A
R 1EFF : 401-499, 1 24-21-00Page 333 1 1 Aug 01/05 1 1 1CES 1
R **ON A/C 401-499,
R Subtask 24-21-00-420-073-A
R B. Installation of New IDG and Main Oil/Fuel Heat Exchanger
R R (1) Install a new IDG (Ref. TASK 24-21-51-400-040) or (Ref. TASK 24-21-51-400-040).
R R (2) Do not connect the oil-in line (2) to the oil-in port (3) at this time.
R R (3) If the cause of contamination is a leak of the main oil/fuel heat exchanger:
R R (a) Install a new main oil/fuel heat exchanger (Ref. TASK 79-21-20-400-002).
R **ON A/C ALL
Subtask 24-21-00-612-074
C. Flushing of the External Lines
CAUTION : USE ONLY APPROVED TYPES/BRANDS OF LUBRICANTS. DO NOT MIX_______ TYPES//BRANDS OF LUBRICANTS.
NOTE : Approximately 1.5 USgal (5.7 l) of oil will flow into the____ container.
(1) Put the end of the IDG oil-in line (2) in a container 5.7 l (1.5 USgal).
(2) Remove the dust cap (4) from the pressure fill valve (1).
(3) Connect the pressure fill hose (5) of the TANK - ENGINE OIL FILLING UP (DH13PM) to the pressure fill valve (1).
(4) Use a pump to fill the IDG with filtered OILS (Material No. 03-002) until: - the color of the oil that flows from the IDG oil-in line (2) is the same as the color of the oil that you put into the IDG, - or until you collect 3.8 l (1.0038 USgal) to 5.7 l (1.5057 USgal) of oil from the IDG oil-in line (2).
Subtask 24-21-00-420-074
D. Connection of the IDG Oil-in Line
CAUTION : USE TWO WRENCHES TO HOLD THE FITTINGS WHEN YOU TORQUE THE
_______ OIL-IN AND OIL-OUT LINES. IF NOT YOU CAN TRANSMIT TOO MUCH TORQUE TO THE IDG FITTINGS AND CAUSE DAMAGE TO THE IDG BOSSES.
(1) Connect the IDG oil-in line (2) to the oil-in port (3). Use two wrenches, one to hold and the other to TORQUE the IDG oil-in line (2) to between 75 and 83.3 lbf.ft (10.16 and 11.29 m.daN).
Subtask 24-21-00-612-075
E. Fill the IDG with oil or add oil in the after a level check (Ref. TASK 12-13-24-612-041).
5. Close-up
________ Subtask 24-21-00-410-074
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
(3)
Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
-
FOR 1000EM1
437AL, 438AR
-
FOR 1000EM2
447AL, 448AR
(4) Remove the warning notice(s). Subtask 24-21-00-862-056
B. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
1EFF : ALL 1 24-21-00Page 335 1 1 Aug 01/05R 1 1 1CES 1
TASK 24-21-00-612-046
IDG Oil-Type Change
WARNING : BE CAREFUL WHEN YOU WORK ON THE ENGINE COMPONENTS IMMEDIATELY AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS CAN STAY HOT FOR UP TO ONE HOUR.
WARNING : WEAR GOGGLES, INSULATED GLOVES AND OTHER PROTECTIVE CLOTHES.
_______ HOT OIL CAN BURN YOUR EYES AND SKIN. IF OIL TOUCHES YOUR EYES OR SKIN, GET MEDICAL AID.
CAUTION : DO NOT OPERATE THE IDG:
_______
-
IF IT CONTAINS TOO MUCH OIL
-
IF IT DOES NOT CONTAIN ENOUGH OIL
IF YOU DO, YOU CAN CAUSE DAMAGE TO THE IDG.
CAUTION : USE ONLY NEW CANS OF OIL WHEN YOU FILL THE IDG WITH OIL OR ADD OIL TO
_______ THE IDG. THE CONTAMINATION IN OIL THAT STAYS IN OPEN CANS CAN CAUSE FAST DETERIORATION OF THE OIL AND WILL DECREASE THE LIFE OF THE IDG.
CAUTION : DO NOT USE SOLVENTS THAT CONTAIN CHLORINE TO CLEAN THE EQUIPMENT
_______ (PUMP, HOSES, TANK AND FUNNEL) USED TO FILL THE IDG WITH OIL. CHLORINE CONTAMINATION OF THE OIL CAN CAUSE FAST DETERIORATION OF THE OIL AND WILL DECREASE THE LIFE OF THE IDG.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源1(55)
