-
the ENTER ID #:'9999' comes into view,
-
the MAINTENANCE MODE selection page comes into view.
On the SCU 11MH, on the monitor:
-
the cursor move to CONFIGURATION,
-
the CONFIGURATION selection page comes into view.
On the SCU 11MH, on the monitor:
-
the cursor move to SVDU/MONITOR CONFIG,
-
the SVDU/MONITOR CONFIG selection page comes into view.
On the SCU 11MH, on the monitor:
-
the cursor move to SVDU CONFIG,
-
the SVDU CONFIG selection page comes into view.
On the SCU 11MH, on the monitor:
-
the cursor move to PREDEFINED CONFIG,
-
the SVDU CONFIG/ENTER SYDU TABLE #/(1-50) page comes into view.
R 1EFF : 301-399, 1 23-36-00Page 314 1 1 Nov 01/04 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R 9. On the SCU 11MH, on the key pad:
R R R - push the up or down arrow membrane switch for the selection of the table '20',
R R R R R - push the ENTER membrane switch.
R R R R R R R R R R
R 10. On the SCU 11MH, on the key pad:
R R R R - push the CLEAR membrane switch again and again until the AUTO MODE selection page comes into view.
R 11. On the SCU 11MH:
R R - push the pushbutton switch MASTER POWER.
R R R
On the SCU 11MH, on the monitor:
-the item SVDU TABLE # '20' comes into view,
-SVDU INITIALIZATION in PROGRESS XXX% COMPLETED
When the initialization process is completed: - on the SVDU CONFIG page the following
messages come into the view:
SVDU
INITIALIZATION
COMPLETED
CHAIN A:10 SVDU
CHAIN B:10 SVDU
On the SCU 11MH, on the monitor:
On the SCU 11MH:
-the integral light of the MASTER POWER pushbutton switch goes off.
NOTE : Wait for a minimum of 10 seconds
____ after the SCU power-off, then continue with the configuration.
R 1EFF : 301-399, 1 23-36-00Page 315 1 1 Nov 01/04 1 1 1CES 1
R Subtask 23-36-00-970-051-A
R B. Configuration of the Programmable System Control System
R -------------------------------------------------------------------------------
R ACTION RESULT
R -------------------------------------------------------------------------------
R 1. In the Video Control Center (VCC) In the VCC 10MH:
R 10MH:
R - push the VCC MASTER POWER - the integral light of the VCC MASTER
R SWITCH pushbutton switch. POWER SWITCH pushbutton switch comes
R on.
R 2. On the PES video System Control On the SCU 11MH:
R Unit (SCU) 11MH:
R - push the pushbutton switch - the integral light of the MASTER
R MASTER POWER. POWER pushbutton switch comes on,
R - all LED come on while the SCU 11MH
R does the self test of the system,
R - the green LED SYSTEM TEST/PASS comes
R on when the self test is complete.
R On the PES video SCU 11MH, on the
R monitor:
R - the PROGRAMMABLE PSCU page comes into
R view.
R NOTE : Wait for a minimum of 3 minutes after the SCU power-on, then continue
____
R with the procedure.
R
R
R 3. On the SCU 11MH, MODE SELECT
R area:
R - push and hold the menbrane
R switch for 5 seconds.
R 4. On the SCU 11MH, on the key pad:
R - push four times the '9'
R membrane switch.
-
the AUTO MODE selection page comes into view.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊2(52)
