1EFF : ALL 1 23-33-31Page 406 1 1 Aug 01/05 1 1 1CES 1

 IFE CENTER - REMOVAL/INSTALLATION
_________________________________ TASK 23-33-36-000-001 Removal of the IFE CENTER (310MK)
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
 No specific circuit breaker(s) safety clip(s)
 No specific access platform 1.6 m (5 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-33-36-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 23-33-36-865-050
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
123VU BUS 2/210XP/SPLY 7XN2 AF02
 1EFF : ALL 1 23-33-36Page 401 1 1 Feb 01/03 1 1 1CES 1 Subtask 23-33-36-010-050

 B. Get Access
 (1)
 Put the access platform in position at the access door 824 in zone

 128.

 (2)
 Open the access door 824.

 4. Procedure
_________
 (Ref. Fig. 401/TASK 23-33-36-991-001) Subtask 23-33-36-020-050
 A. Removal of the IFE CENTER
 (1)
 Loosen the nuts (3).

 (2)
 Lower the nuts (3).

 (3)
 Pull the IFE CENTER (5) on its rack (2) to disconnect the electrical connectors (1).

 (4)
 Remove the IFE CENTER (5) from its rack (2).

 (5)
 Put blanking caps on the disconnected electrical connectors (1).

 1EFF : ALL 1 23-33-36Page 402 1 1 Feb 01/03 1 1 1CES 1

 IFE CENTER
 Figure 401/TASK 23-33-36-991-001
 1EFF :  ALL  1  23-33-36 Page 403 
1  1  Feb 01/03
 1  1
 1CES  1

 TASK 23-33-36-400-001
 Installation of the IFE CENTER (310MK)

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.6 m (5 ft. 3 in.)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-33-00-740-002 BITE-Test of the Passenger Entertainment System
 (Music) with the Programming and Test Panel (PTP) 52-41-00-410-002 Close the Avionics Compartment Doors after Access 23-33-36-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 23-33-36-860-050
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the access platform is in position at the access door 824 in zone 128.

 (2)
 Make sure that the access door 824 is open.

 1EFF : ALL 1 23-33-36Page 404 1 1 Feb 01/03 1 1 1CES 1 Subtask 23-33-36-865-051

 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
123VU BUS 2/210XP/SPLY 7XN2 AF02
 4. Procedure
_________
 (Ref. Fig. 401/TASK 23-33-36-991-001) Subtask 23-33-36-420-050
 A. Installation of the IFE CENTER
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Remove the blanking caps from the electrical connectors (1).

 (4)
 Make sure that the electrical connectors (1) are clean and in the correct condition.