B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
123VU BUS 2/210XP/SPLY 7XN2 AF02
 4. Procedure
_________
 (Ref. Fig. 401/TASK 23-33-37-991-001) Subtask 23-33-37-420-050
 A. Installation of the CONTROLLER - IFE
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Remove the blanking caps from the electrical connectors (1).

 (4)
 Make sure that the electrical connectors (1) are clean and in the correct condition.

 (5)
 Install the CONTROLLER - IFE (5) in its rack (2).

 (6)
 Push the CONTROLLER - IFE (5) on its rack (2) to connect the electrical connectors (1).

 (7) Engage the nuts (3) on the lugs (4) and tighten. Subtask 23-33-37-865-053
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 7XN2
 Subtask 23-33-37-740-050
 C. Do the BITE test of the IFE CENTER (Ref. TASK 23-33-00-740-002).
 1EFF : ALL 1 23-33-37Page 405 1 1 Feb 01/03 1 1 1CES 1

 5. Close-up
________ Subtask 23-33-37-410-050
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the access door 824 (Ref. TASK 52-41-00-410-002).

 (3)
 Remove the access platform(s).

 1EFF : ALL 1 23-33-37Page 406 1 1 Feb 01/03 1 1 1CES 1

 SERVER - IFE - REMOVAL/INSTALLATION
___________________________________ TASK 23-33-39-000-001 Removal of the SERVER - IFE (312MK)
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
 No specific circuit breaker(s) safety clip(s)
 No specific access platform 1.6 m (5 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-33-39-991-001 Fig. 401
 3. Job Set-up
__________ Subtask 23-33-39-865-050
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
123VU BUS 2/210XP/SPLY 7XN2 AF02
 1EFF : ALL 1 23-33-39Page 401 1 1 Feb 01/03 1 1 1CES 1 Subtask 23-33-39-010-050

 B. Get Access
 (1)
 Put the access platform in position at the access door 824 in zone

 128.

 (2)
 Open the access door 824.

 4. Procedure
_________
 (Ref. Fig. 401/TASK 23-33-39-991-001) Subtask 23-33-39-020-050
 A. Removal of the SERVER - IFE
 (1)
 Loosen the nuts (3).

 (2)
 Lower the nuts (3).

 (3)
 Pull the SERVER - IFE (5) on its rack (2) to disconnect the electrical connectors (1).

 (4)
 Remove the SERVER - IFE (5) from its rack (2).

 (5)
 Put blanking caps on the disconnected electrical connectors (1).

 1EFF : ALL 1 23-33-39Page 402 1 1 Feb 01/03 1 1 1CES 1

 SERVER - IFE
 Figure 401/TASK 23-33-39-991-001
 1EFF :  ALL  1  23-33-39 Page 403 
1  1  Feb 01/03
 1  1
 1CES  1

 TASK 23-33-39-400-001
 Installation of the SERVER - IFE (312MK)

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊2(14)