S 485-174
(3)
Install a brake pressure gage assembly in the bleed port of the number 1 wheel brake.
S 865-173
(4)
Pressurize the right hydraulic system and reservoir (AMM 29-11-00).
S 715-175
(5)
Put the autobrake selector switch on panel P1-3 to the RTO position and make sure that it stays in that position.
S 715-176
(6)
Put the brake test switch on the Antiskid/Autobrake Control Unit, M102, to the A/B position.
(7)
Push in and hold the ENABLE/VERIFY switch.
S 715-178
(8)
Push in the VERIFY switch and release the ENABLE/VERIFY and VERIFY switches.
S 715-177
32-42-00
ALL ú ú 10 Page 525 ú May 28/99
A
757 MAINTENANCE MANUAL
S 715-179
(9)
Make sure that you have these indications:
(a)
The M102 display shows BRK RTO.
(b)
Pressure indication on the brake pressure gage for wheel No. 1 brake goes to 2,900 |100 psi for approximately 15 seconds, and then decreases to less than 100 psi.
(c)
The autobrake selector switch on the P1-3 panel goes to the OFF position.
S 715-180
(10)
Put the brake test rotary switch on the M102 to the NORM position.
S 715-181
(11)
Push in and release the RESET button on the M102.
S 715-182
(12)
Remove power from the right and left hydraulic system (AMM 29-11-00).
S 715-183
(13)
Remove the brake pressure gage from wheel number 1 and put the brake bleed port back to the normal configuration.
TASK 32-42-00-945-184
9. Put the Airplane Back to Its Usual Condition____________________________________________
A. References
(1)
AMM 24-22-00/201, Electrical Power - Control
(2)
AMM 06-46-00/201, Entry, Service, and Cargo Doors (Major Zone 800) Access Doors and Panels
(3)
AMM 25-50-03/401, Bulkhead
(4)
AMM 29-11-00/201, Pressurize/Depressurize Main Hydraulic System
B.
Access
(1)
Location Zones
211 Control Cabin, Left
212 Control Cabin, Right
731 Landing Gear Left
741 Landing Gear Right
120 Main Equipment Center, Right
32-42-00
ALL ú ú 07 Page 526 ú Sep 28/99
A
757 MAINTENANCE MANUAL
(2)
Access Panel
119AL Main Equipment Center
C.
Procedure
S 865-185
(1)
Put the L, R and C IRUs to the OFF position.
S 865-186
(2)
Remove the power from the left and right hydraulic systems
(AMM 29-11-00).
S 085-187
(3)
Remove the brake pressure gages, if installed, and put the brake bleed port back to its usual condition.
S 865-188
(4)
Pressurize the right hydraulic system and reservoir (AMM 29-11-00).
S 865-189
(5)
Set the parking brake.
S 865-190
(6)
Push in the RESET button on the Antiskid/Autobrake Control Unit, M102 to clear the memory (the display will show MEM CLR).
S 415-201
(7)
AIRPLANES WITH ANTISKID/AUTO BRAKE CONTROL UNIT OF THE E5 RACK (FIG. 501); Do the steps that follows:
(a)
On the forward bulkhead in the forward cargo compartment, install the access panel for the E5 rack (AMM 25-50-03/401).
(b)
Close the forward cargo door, 821.
S 865-210
(8)
Remove the power from the right hydraulic system if it is not necessary (AMM 29-11-00).
(9)
Remove the electrical power if it is not necessary (AMM 24-22-00).
S 865-211
32-42-00
ALL ú ú 10 Page 527 ú Sep 28/99
A
757 MAINTENANCE MANUAL
ANTISKID/AUTOBRAKE SYSTEM - INSPECTION/CHECK
____________________________________________
1. General_______
A. This section contains these tasks:
(1)
An operational test of the thrust lever switch for a Refused Takeoff (RTO) configuration.
(2)
A test for correct operation and indications for part of the antiskid/autobrake system as follows:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(19)
