S 865-157
(74)
Erase the EICAS ECS/MSG AUTO EVENT page.
S 865-158
(75)
Open this circuit breaker on the overhead panel, P11:
(a)
11S23, LANDING GEAR POS SYS 2
S 735-159
(76)
Make sure the EICAS message LDG GEAR MONITOR is shown on the bottom display after 2 seconds.
(a)
Make sure the EICAS messages in the list below show on the bottom display:
GEAR DISAGREE NOSE GEAR DOWN NOSE GEAR LOCKED L GEAR DOWN R GEAR DOWN
32-61-00
ALL ú ú 01 Page 532 ú Dec 20/96
A
757 MAINTENANCE MANUAL
S 735-160
(77)
Move the COMPUTER switch to the R position. Make sure the EICAS message LDG GEAR MONITOR is shown on the bottom display.
(a)
Make sure the EICAS messages on the list below show on the bottom display:
GEAR DISAGREE
NOSE GEAR DOWN
NOSE GEAR LOCKED
L GEAR DOWN
R GEAR DOWN
S 865-161
(78)
Close this circuit breaker on the overhead panel, P11:
(a)
11S23, LANDING GEAR POS SYS 2
S 495-162
(79) Install deactuators on the sensors in the list below:
SENSOR
______
S10057
S10061
S10065
S10066
S10070
S10074
S10078
S10079
S 865-163
(80)
Move the control lever for the landing gear to the UP position.
(81)
Make sure the amber GEAR light is on.
(82)
Erase the EICAS ECS/MSG AUTO EVENT page.
S 735-166
(83)
Make sure the EICAS message LDG GEAR MONITOR is not shown on the bottom display.
S 735-164
S 865-165
32-61-00
ALL ú ú 01 Page 533 ú Dec 20/96
A
757
MAINTENANCE MANUAL
S 495-167
(84) Install or remove the actuators or deactuator on the sensors in the list below:
SENSOR______ ACTUATOR________ DEACTUATOR__________
S10069 Install --
S10073 Install --
S10077 Install --
S10078 --- Remove
S 735-168
(85)
Make sure the amber GEARS light is off. Make sure the EICAS message PSEU BITE is shown on the bottom display after 2 seconds.
S 735-169
(86)
Move the COMPUTER switch to the L position. Make sure the EICAS message PSEU BITE is shown on the bottom display.
S 495-170
(87)
Install a deactuator on the sensor S10078.
S 735-171
(88)
Make sure the amber GEAR light is on.
S 095-172
(89)
Remove the actuator or deactuator from the sensors in the list below:
SENSOR______ ACTUATOR________ DEACTUATOR S10073 Remove --S10078 --Remove
S 735-173
(90)
Make sure the amber GEAR light is on.
S 495-174
(91)
Install or remove an actuator on the sensors in the list below:
SENSOR______ ACTUATOR S10069 Remove S10073 Install
S 735-175
(92) Make sure the amber GEAR light is on.
32-61-00
ALL ú ú 01 Page 534 ú Dec 20/96
A
757 MAINTENANCE MANUAL
S 495-176
(93) Install or remove the actuators on the sensors in the list below:
SENSOR______ ACTUATOR
S10069 Install
S10077 Remove
S 735-177
(94)
Make sure the amber GEAR light is on.
S 865-178
(95)
Move the control lever for the landing gear to the DN position.
S 865-179
(96)
Erase the EICAS ECS/MSG AUTO EVENT page.
S 095-181
WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO REMOVE TO DOOR LOCKS.
_______ THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY OR DAMAGE TO EQUIPMENT.
(97)
Remove the door locks from the main landing gear doors and close the main landing gear doors (AMM 32-00-15/201).
S 445-191
(98)
Put the safety-sensitive systems back to their initial conditions (AMM 32-09-02/201).
S 865-183
(99)
Remove electrical power if it is not necessary (AMM 24-22-00/201).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 起落架 CHAPTER 32 - LANDING GEAR 3(156)
