CRANK
8.
WASHER
INBD
9. NUT
7.
BOLT
8.
WASHER ROD
23. CONTROL
16.
SHAFT 9. NUT
17.
NUT
NWSB 18. WASHER 11. INPUT ROD
22. STEERING LINK CABLE 12. BOLT TENSIONER
13. WASHER NGPPB 14. NUT
NGPPA LOWER
SEE B BRACKET
15. CABLE
20. ECCENTRIC ARM GUARD BRACKET LOWER
21. CLUTCH
ECCENTRIC19. ECCENTRIC NOSE STEERING
DRUMDRUM
RIG PIN HOLE NS6
A
BOTTOM VIEW
B
Rudder Pedal Steering Interconnect Installation
Figure 401 (Sheet 1)
32-51-05
ALL ú ú 01 Page 403 ú May 28/99
A
757
MAINTENANCE MANUAL
7. BOLT 4. BOLT 24. SPACER 16. SHAFT
UPPER SUPPORT 8. WASHER
5. NUT BRACKET (REF) 9. NUT
17. NUT 6. WASHER
25. BEARING (3 LOCATIONS) 18. WASHER
11. INPUT ROD ASSEMBLY
24. SPACER
1. QUADRANT
21. CLUTCH 10. STEERING CRANK
26.
SPACER
27.
SPACER
20. ECCENTRIC ARM
28. SPACER
15. CABLE GUARD
LOWER SUPPORT 19. ECCENTRIC DRUM BRACKET (REF)
TIE ROD (REF)
OUTBD
A-A
RUDDER RIG RUDDER LEFT FORWARD QUADRANTPIN HOLE AND JACKSHAFT ASSEMBLY
R2
INBD FWD TO INTERCONNECT MECHANISM
C
Rudder Pedal Steering Interconnect Installation Figure 401 (Sheet 2)
32-51-05
ALL ú ú 01 Page 404 ú May 28/99
A
757
MAINTENANCE MANUAL
NGPPB NGPPA
CONTROL QUADRANT RIG PIN NS7
SEE A
QUADRANT
SPRING
CARTRIDGE
BOLT
UPPER TORSION LINK
1
A
LOWER TORSION
LINK DISCONNECTED
1
Nose Wheel Steering Spring Cartridge Installation Figure 402
32-51-05
ALL ú ú 01 Page 405 ú May 28/99
A
757 MAINTENANCE MANUAL
S 034-014
(14)
Remove the mounting bolt for the interconnect installation of the rudder pedal steering.
S 024-015
(15)
Remove the interconnect mechanism assembly for the rudder pedal steering.
S 034-016
(16)
You can remove the top shaft retaining nut and lockwasher (View AA, Fig. 401) if it is necessary to disassemble the interconnect mechanism on the bench.
TASK 32-51-05-404-017
3. Install Rudder Pedal Steering Interconnect__________________________________________
A. Equipment
(1)
Rig Pins: Kit B20003-XX (AMM 20-10-24/201)
(a)
NS1 - P/N B20003-20
(b)
NS2 - P/N B20003-24
(c)
NS3 - P/N B20003-5
(d)
NS5 - P/N B20003-5
(e)
NS6 - P/N B20003-5
(f)
NS7 - P/N B20003-15
(g)
R2 - P/N B20003-22
(2)
Cable Tensiometer - 0 to 200 pound range for
3/32 inch diameter cable (commercially
available)
(3)
Towing Lever Lockpin - A09003-1
32-51-05
ALL ú ú 03 Page 406 ú May 28/99
A
757
MAINTENANCE MANUAL
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Quadrant - Steering | 32-51-05 | 01 | 345 | | | 2 | Spring - Extension, Inner | | | 100 | | | 3 | Spring - Extension, Outer | | | 105 | | | 4 | Bolt | | | 155 | | | 5 | Nut | | | 205 | | | 6 | Washer | | | 165 | | | 7 | Bolt | | | 5 | | | 8 | Washer | | | 10 | | | 9 | Nut | | | 15 | | | 10 | Crank - Steering | | | 250 | | | 11 | Input Rod Assembly | | | 20 | | | 12 | Bolt | | | 445 | | | 13 | Washer | | | 450 | | | 14 | Nut | | | 455 | | | 15 | Guard - Cable | | | 440 | | | 16 | Shaft | | | 220 | | | 17 | Nut | | | 210 | | | 18 | Washer | | | 170 | | | 19 | Drum - Eccentric | | | 435 | | | 20 | Arm, Eccentric | | | 415 | | | 21 | Clutch | | | 290 | | | 22 | Tensioner, Steering Link Cable | | | 325 | | | 23 | Control Rod Assembly | | | 145 | | | 24 | Spacer | | | 180 | | | 25 | Bearing | | | 215 | | | 26 | Spacer | | | 185 | | | 27 | Spacer | | | 190 | | | 28 | Spacer | | | 195 | 2.......….......…...................................…...........….....…........1 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 起落架 CHAPTER 32 - LANDING GEAR 3(122)
