(a)  
11S14, AUTOBK ANTISKID TEST IND 1

 S 715-065
 (11)
 Make sure that the AUTOBRAKES selector switch stays armed, the AUTOBRAKES light goes off, and the AUTOBRAKES advisory message does not appear on the EICAS display.

 S 865-066

 (12)
 Open this circuit breaker on the P11 panel:

 (a)  
11S21, AUTOBK ANTISKID TEST IND 2

 S 715-067
 (13)
 Make sure that the AUTOBRAKES selector switch goes to DISARM, the AUTOBRAKES light comes on, and the AUTOBRAKES advisory message appears on the EICAS display.

 S 865-068

 (14)
 Close these circuit breakers on the P11 panel:

 (a)  
11S14, AUTOBK ANTISKID TEST IND 1

 (b)  
11S21, AUTOBK ANTISKID TEST IND 2

 S 715-069
 (15)
 Put the AUTOBRAKES selector switch to position 1.  Make sure that the switch arms, the AUTOBRAKES light goes off and the AUTOBRAKES message goes out of view.

 S 865-070

 (16)
 Push in and hold the pilots' right brake pedal.

 S 715-071

 (17)
 Make sure that the AUTOBRAKES selector switch moves to DISARM, the AUTOBRAKES light come on and AUTOBRAKES advisory message appears on the EICAS display.

 S 715-072

 (18)
 Push and hold the ENABLE/VERIFY switch and then push the VERIFY switch. Release the two switches at the same time.

 (19)
 Make sure that the M102 unit display shows PRES R.

 (20)
 Release the pilots' right brake pedal.

 S 715-075

 (21)
 Put the AUTOBRAKES selector switch in position 1.  Make sure that it arms, the AUTOBRAKES light goes off and the AUTOBRAKES message goes out of view.

 S 715-073
 S 865-074
 

 32-42-00
 ALL  ú ú 03 Page 516 ú Mar 20/94
 
A
757
MAINTENANCE MANUAL

 S 715-076
 (22)
 Push in and hold the pilots' left brake pedal.

 S 715-077

 (23)
 Make sure that the AUTOBRAKES selector switch moves to the DISARM position, the AUTOBRAKES light comes on and the AUTOBRAKES message appears on the EICAS advisory display.

 S 715-078

 (24)
 Push and hold the ENABLE/VERIFY switchd, and then push the VERIFY switch. Release the switches at the same time.

 S 715-079

 (25)
 Make sure that the M102 unit display shows PRES L.

 S 715-080

 (26)
 Release the pilots' left brake pedal.

 S 715-081

 (27)
 Put the AUTOBRAKES selector switch in the MAX AUTO position.  Make sure that the switch arms, the AUTOBRAKES light goes off and the AUTOBRAKES message goes out of view.

 S 715-082

 (28)
 Hold the AUTOBRAKES selector switch in the MAX AUTO position.

 S 715-083

 (29)
 Move the right thrust lever forward from the idle position.

 S 715-084

 (30)
 Make sure that the AUTOBRAKES light comes on and the AUTOBRAKES advisory message appears on the EICAS display.

 S 715-085

 (31)
 Push and hold the ENABLE/VERIFY switch, and then push the VERIFY switch. Release the two switches at the same time.

 (32)
 Make sure that the M102 unit display shows THR R1.

 S 715-087

 (33)
 Push and release the VERIFY switch.  Make sure that the M102 unit display shows THR R2.

 S 715-088

 (34)
 Release the AUTOBRAKES selector switch and make sure that it moves to the DISARM position.

 (35)
 Put the right thrust lever in the idle position.

 S 715-086
 S 715-089
 

 32-42-00
 ALL  ú ú 03 Page 517 ú Mar 20/94
 
A
757 MAINTENANCE MANUAL
 S 715-090
 (36)
 Push and release the RESET button on the M102 unit and stop 5 |3 seconds. Make sure that the M102 display shows MEM CLR.

 S 715-091

 (37)
 Put the AUTOBRAKES selector switch in the MAX AUTO position.  Make sure that the switch arms, the AUTOBRAKES light goes off and the AUTOBRAKES message goes out of view.

 S 715-092

 (38)
 Hold the AUTOBRAKES selector switch in the MAX AUTO position.

 S 715-093

 (39)
 Move the left thrust lever forward from the idle position.

 S 715-094

 (40)
 Make sure that the AUTOBRAKES light comes on and the AUTOBRAKES message appears on the EICAS advisory display.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(15)