(2)
Up sensors for the nose landing gear (Sys 2), S10077
(3)
Down sensors for the nose landing gear (Sys 1), S10066
(4)
Down sensors for the nose landing gear (Sys 2), S10079
(5)
Locked sensors for the nose landing gear (Sys 1), S10065
(6)
Locked sensors for the nose landing gear (Sys 2), S10078
(7)
Door closed sensors for the nose landing gear (Sys 1), S10243
(8)
Door closed sensors for the nose landing gear (Sys 2), S10081
TASK 32-61-03-002-001
2. Remove the Proximity Sensor for the Nose Landing Gear_____________________________________________________
A. References
(1)
AMM 32-00-15/201, Landing Gear Door Locks
(2)
AMM 32-00-20/201, Landing Gear Downlocks.
B.
Prepare for the Removal
S 492-002
(1)
Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
(2)
Make sure the chocks are installed on the wheels.
S 492-003
S 492-004
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(3) Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
NOTE: The doors for the nose and the main landing gear open at the
____ same time when you use the ground release.
32-61-03
ALL ú ú 01 Page 201 ú Jan 28/02
A
757 MAINTENANCE MANUAL
S 862-005
(4)
Make sure the electrical power is removed (AMM 24-22-00/201).
C.
Remove the Up, Down, and Door Closed Sensor for the Nose Landing Gear (Fig. 201 and 202)
S 022-006
(1)
Remove the screws (2) that hold the sensor to the bracket, and remove the sensor (1).
S 032-007
(2)
Loosen the clamps that hold the wire bundle.
S 932-008
CAUTION:_______WRITE DOWN THE WIRE COLOR CODE. THIS WILL PERMIT THE CORRECT INSTALLATION OF THE SENSOR WIRES AND PREVENT THE MALFUNCTION OF THE POSITION INDICATION SYSTEM FOR THE LANDING GEAR.
(3)
Put a tag with the color code on the wire for the installation.
S 032-009
(4)
Cut the sensor wires at the wire bundle splices.
S 032-010
(5)
Remove the sensor wire from the wire bundle.
D.
Remove the Locked Sensor for the Nose Landing Gear (Fig. 203)
S 942-011
(1) Find the wire bundle (3) near the conduit connect panel (1) at the top of the wheel well.
S 932-012
CAUTION:_______WRITE DOWN THE WIRE COLOR CODE. THIS WILL PERMIT THE CORRECT INSTALLATION OF THE SENSOR WIRES AND PREVENT THE MALFUNCTION OF THE POSITION INDICATION SYSTEM FOR THE LANDING GEAR.
(2)
Put a tag with the color code on the wire for the installation.
(3)
Cut the sensor wires at the wire bundle splices.
S 032-013
NOTE: The wire bundle ties can be cut to make work on the wires
____
easier.
S 492-014
(4) Attach a line to the sensor wires.
32-61-03
ALL ú ú 01 Page 202 ú Jan 28/02
A
757 MAINTENANCE MANUAL
RETRACT WHEEL WELL ACTUATOR AFT WALL
NOSE LANDING GEAR DRAG STRUT
SEE A
FWD
BA
WHEEL WELL CEILING
BA
NOSE LANDING GEAR DRAG STRUT
SENSOR
WIRING
NOSE LANDING GEAR DOWN SENSOR
NOSE LANDING GEAR UP SENSOR
WHEEL WELL AFT WALL
A
Nose Landing Gear Up and Down Position Sensors Figure 201 (Sheet 1)
32-61-03
ALL ú ú 01 Page 203 ú Sep 20/95
A
757 MAINTENANCE MANUAL
1. NOSE LANDING GEAR UP SENSOR
A-A
1. NOSE LANDINGGEAR DOWN SENSOR WHEEL WELL CEILING
B-B
Nose Landing Gear Up and Down Position Sensor
Figure 201 (Sheet 2)
32-61-03
ALL ú ú 01 Page 204 ú Sep 20/95
A
757 MAINTENANCE MANUAL
WHEEL WELL FORWARD WALL
SEE A BOLT BELLCRANK
B
A
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(165)
