(3)  
Six other fuse pins connect the gear to wing structure. One fuse pin attaches the trunnion link into the forward trunnion bearing. Four fuse pins attach the aft trunnion bearing housing to the main landing gear support beam. One more fuse pin attaches the reaction link to the forward trunnion bearing housing at the outboard end of the link.

 (4)  
The main landing gear support beam is attached to wing structure at the outboard end by another fuse pin. This pin is designed to fail first under excessive vertical loads.

 32-11-00
 ALL  ú ú 01 Page 5 ú Sep 15/83
 
A
757 MAINTENANCE MANUAL
 MAIN GEAR - REMOVAL/INSTALLATION
________________________________
 1.  General
_______
 A.  This procedure contains two tasks. The first task removes the main
 landing gear. The second task installs the main landing gear. GUN B. When you lift the airplane to remove the main landing gear, do the steps GUN that follow: GUN (1) Adjust the height of the airplane on the jacks to permit removal of GUN the wheel, brake and brake rod (AMM 32-45-01/401, AMM 32-41-10/401 GUN and AMM 32-11-19/401). GUN (2) Install the dolley. GUN C. When the main landing gear is installed, remove the dolley. Install the GUN brakes, brake rods and wheels after you install the positioner actuator.
 TASK 32-11-01-004-077
 2.  Remove the Main Landing Gear (Fig. 401, 402)
____________________________
 A.  Equipment
 (1)
B32006-13 MLG Shock Strut Positioner Link

 (2)
B32011-14 MLG Thread Protector Set

 (3)  
B32018-1 MLG Trunnion Link to Strut
 Alignment Pin

 (4)
757-200, -300;

 B32020-45 MLG Removal/Instl Equipment (Recommended)

 (5)
757-200;

 B32020-1, -33 MLG Removal/Instl Equipment (Alternative)

 (6)
B32029-1 MLG Trunnion Link Support Equipment

 (7)  
B32044-12 MLG Structural Fuse Pin Puller
 Equipment

 (8) F70312-38 Crowfoot Wrench GUN (9) 0-32-58131 MLG Removal/Installation Dolley
 (10)
 Automotive-Type Axle Jacks -Commercially Available

 B.  
References

 (1)
AMM 07-11-01/201, Jacking Airplane

 (2)
AMM 24-22-00/201, Electrical Power - Control

 (3)
AMM 29-11-00/201, Pressurize/Depressurize Main Hydraulic System

 (4)
AMM 32-00-15/201, Landing Gear Door Locks

 (5)
AMM 32-00-20/201, Landing Gear Downlocks

 (6)
AMM 32-12-04/401, Main Gear Strut Door

 (7)
AMM 32-32-15/401, Main Gear Truck Positioner Actuator

 (8)
AMM 57-54-07/401, MLG Trunnion Fairing

 32-11-01
 ALL  ú ú GUN Page 401 ú Jan 28/01
 
A

757
MAINTENANCE MANUAL

 C. Access
 (1)  
Location Zones
 119/120 Main Equipment Center
 211/212 Control Cabin
 500/600 Left Wing/Right Wing
 731/741 Main Landing Gear (MLG)
 732/742 MLG Body Doors
 733/743 MLG Oleo Doors

 (2)  
Access Panel
 119BL Main Equipment Center

 D.
Prepare for Removal of the Main Landing Gear

 S 494-001
 (1)  Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
 S 494-003
 WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(77)