F.
Simulate the Air Mode

 32-09-02
 ALL  ú ú 13 Page 207 ú May 28/02
 
A

757
MAINTENANCE MANUAL

 S 042-053
 WARNING:_______ DO THE PROCEDURE TO PREPARE THE SAFETY-SENSITIVE SYSTEMS FOR
 AIR MODE SIMULATION.  IF YOU DO NOT DO THE PROCEDURE BEFORE YOU
 SIMULATE AIR MODE, INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN

 OCCUR.
 (1)  
Do the task to Prepare the Safety-Sensitive Systems for Air Mode Simulation before you simulate the air mode.

 S 862-063

 (2)  
Put the air/ground relay system in the air mode (Option 1).

 NOTE: If you do not want to lift the airplane with jacks, do the
____ steps in Option 2. You will need actuators and deactuators for the proximity sensors if you use Option 2. If a landing gear or air/ground proximity sensors have been removed, then do the steps which follow option 2 in install proximity sensors on the affected gear.
 (a)  Lift the airplane with jacks (Ref 07-11-01/201).
 S 862-054
 (3)  
Put the air/ground relay system in the air mode (Option 2).

 (a)  
Make sure the downlocks are installed on the nose and main landing gear (Ref 32-00-20).

 (b)  
Put the chocks below the wheels.

 (c)  
Put actuators and deactuators on the proximity sensors of the landing gear to simulate the air mode (Fig. 201): 1) Put the deactuators on the truck tilt sensors of the main

 landing gear that follow: a) S10062 for system 1 on the left main landing gear b) S10060 for system 1 on the right main landing gear c) S10064 for system 2 on the left main landing gear d) S10059 for system 2 on the right main landing gear
 

 32-09-02
 ALL  ú ú 03 Page 208 ú May 28/99
 
A

757
MAINTENANCE MANUAL

MAIN LANDING GEAR SHOCK STRUT (REF)
SENSOR, S10697
(RIGHT GEAR ONLY)MAIN LANDING GEAR
1 TRUCK TILT SENSORS
SEE A
SENSOR,
S10064 LEFT (SYSTEM 2)
S10059 RIGHT (SYSTEM 2)

SENSOR,FWD S10062 LEFT (SYSTEM 1) S10060 RIGHT (SYSTEM 1)
MAIN LANDING GEAR TRUCK TILT SENSORS
MAIN LANDING GEAR
A
P62 PANEL (REF)
NOSE LANDING GEAR NOT COMPRESSED
NOSE LANDING 
SENSORS  GEAR STRUT 
SEE  B  P63 PANEL (REF)  (REF) 

SYSTEM 2 SENSOR, S10068
SYSTEM 1 SENSOR, S10067FWD SENSOR TARGET (REF) (NOSE LANDING GEAR IN THE FULLY COMPRESSED
NOSE LANDING GEAR
POSITION)
NOSE LANDING GEAR NOT COMPRESSED SENSORS
B
1
NOT INSTALLED ON ALL AIRPLANES
Sensor Location of the Air/Ground Relays for the Flight Mode Simulation Figure 201
K24917
 

 32-09-02
 ALL  ú ú 02 Page 209 ú May 28/99
 
A

757 MAINTENANCE MANUAL
 e)  IF INSTALLED; S10697 sensor on the right main landing gear
 2)  Put the actuators on the not compressed sensors of the nose landing gear that follow: a) S10067 for system 1 on the nose landing gear b) S10068 for system 2 on the nose landing gear
 S 862-090
 (4)  
If a landing gear or tilt sensor has been removed, then do these steps:

 (a)  
To connect a main landing gear sensor, do the applicable steps in this procedure: AMM 32-09-07/201.

 (b)  
To connect a nose landing gear sensor, do the applicable steps in this procedure: AMM 32-09-08/201.

 (c)  
Put the deactuators on the truck tilt sensors of the main landing gear.

 (d)  
Put the actuators on the not compressed sensors of the nose landing gear.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(32)