(a)  
11C19, LANDING GEAR POS SYS 2 ALTN

 (b)  
11C30, LANDING GEAR POS SYS 1

 32-09-02
 ALL  ú ú 01 Page 502 ú Sep 20/92
 
A

757 MAINTENANCE MANUAL
 (c)  
11R36, PROX SW TEST

 (d)  
11S15, LANDING GEAR AIR/GND SYS1

 (e)  
11S19, LANDING GEAR AIR/GND SYS2

 (f)  
11S23, POS SYS 2

 (g)  
EICAS circuit breakers (6 locations)

 S 865-007
 (6)  
Make sure the control lever for the landing gear is in the DN position.

 S 865-008

 (7)
Remove the pressure from the left hydraulic system (Ref 29-11-00).

 S 875-011
 WARNING:_______BE CAREFUL WHEN YOU BLEED THE HYDRAULIC FLUID. THERE IS PRESSURE ON THE HYDRAULIC FLUID. WHEN YOU BLEED THE PRESSURIZED HYDRAULIC FLUID, IT CAN CAUSE INJURY TO PERSONS.
 CAUTION: PUT A FUNNEL ON THE BLEED PORT ON THE TRUCK TILT POSITIONER OF
_______ THE MAIN LANDING GEAR. THE HYDRAULIC FLUID WILL FLOW APPROXIMATELY THREE FEET FROM THE BLEED PORT. THE HYDRAULIC FLUID CAN CAUSE DAMAGE TO THE EQUIPMENT.
 (8)  
Use the bleed ports on the truck tilt positioners of the main landing gear, to remove the pressure from the positioners.

 F.
Do the Test for the Air/Ground Relays (Fig. 501)

 S 765-010
 (1)  Use a volt/ohmmeter to measure the voltage between pins 6 (+ voltage) and 12 (ground). The connectors to be measured are in column A of Tables 1 and 2. The measured voltage of each connector must be the same as the voltage shown in column B of Tables 1 and 2.
 NOTE: When you measure a 0 VDC, a 500 ohm load resistor or the
____ equivalent must be connected in parallel with the volt/ohmmeter.
 All the voltages are |2.0 volts.
 

 32-09-02
 ALL  ú ú 01 Page 503 ú May 28/02
 
A
757
MAINTENANCE MANUAL

SHOCK STRUT OF THE MAIN LANDING GEAR (REF)
SENSOR S10062 LEFT SYSTEM 1 S10060 RIGHT SYSTEM 1
LOCATION OF THE TRUCK TILT SENSORS
FWD
FOR THE MAIN
LANDING GEAR

SEE A
SENSOR S10064 LEFT SYSTEM 2 S10059 RIGHT SYSTEM 2
LOCATION OF THE TRUCK TILT SENSORS FOR THE MAIN LANDING GEAR
A
MAIN LANDING GEAR
SHOCK STRUT OF THE NOSE LANDING GEAR (REF)
LOCATION OF THE NOT SENSOR (S10068)COMPRESSED SENSOR FOR ON THE RIGHT SIDE
THE NOSE LANDING GEAR OF THE STRUT
SEE B UPPER TORSION LINK (REF)
SENSOR (S10067) ON THE LEFT SIDE OF THE STRUT
SENSOR TARGET (REF)
LOCATION OF THE NOT COMPRESSED SENSOR FOR THE NOSE LANDING GEAR
B
FWD
NOSE LANDING GEAR
System Test for the Air/Ground Relays
Figure 501

 32-09-02
 ALL  ú ú 01 Page 504 ú Sep 20/92
 
A
757 MAINTENANCE MANUAL
 ~........................................................................ | Table 1 | | System 1 Relays (P36) | .......................................................................... | Column | .......................................................................... | A | B (Vdc) | C1 (Vdc) | C2 (Vdc) | D (Vdc) | E (Vdc) | .......................................................................... | D1784 of K10108 | 0.0 | 28.0 | 28.0 | 28.0 | 28.0 | | D606 of K177 | 28.0 | 0.0 | 0.0 | 28.0 | 0.0 | | D582 of K124 | 0.0 | 0.0 | 28.0 | 0.0 | 0.0 | | D586 of K141 | 28.0 | 0.0 | 0.0 | 28.0 | 0.0 | | D596 *[1] of | 28.0 | 0.0 | 0.0 | 28.0 | 0.0 | | K10107 | | | | | | | D1782 of K167 | 28.0 | 28.0 | 0.0 | 28.0 | 0.0 | | D1780 of K135 | 28.0 | 0.0 | 0.0 | 0.0 | 0.0 | | D4708 of K10385 | 28.0 | 28.0 | 0 0 | 28.0 | 0.0 | 2.................…..........…..........…..........…..........…..........1
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(39)