(2)  
Crowfoot Wrench - F70312-36, -47

 B.  
References

 (1)  
AMM 07-11-01/201, Jacking Airplane

 (2)  
AMM 32-00-20/201, Landing Gear Downlocks

 (3)  
AMM 32-12-04/401, Main Gear Strut Door

 (4)  
AMM 32-45-01/401, Main Gear Wheel and Tire

 C.  
Access

 (1)  
Location Zones
 731/741 Main Landing Gear (MLG)
 732/742 MLG Body Doors
 733/743 MLG Oleo Doors

 D.  
Prepare to Remove the Torsion Links

 S 494-029
 WARNING: MAKE SURE THE DOWNLOCKS ARE INSTALLED ON THE NOSE AND MAIN
_______ LANDING GEAR BEFORE YOU MOVE THE CONTROL LEVER FOR THE LANDING GEAR. IF THE CONTROL LEVER IS MOVED WITHOUT THE DOWNLOCKS INSTALLED, THE LANDING GEAR CAN RETRACT AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).

 S 864-002

 (2)  
Put the control lever for the landing gear in the OFF position. Attach a DO-NOT-OPERATE tag.

 32-11-16
 ALL  ú ú 01 Page 401 ú Dec 20/96
 
A
757 MAINTENANCE MANUAL
ANTIROTATION NUT WASHERBOLT (2 LOCATIONS)
END CAP NUT
ASSEMBLY LOWER TORSION
TANG LINK
WASHER
DRAG 
STRUT 
DRAG 
STRUT 
UPPER LINK TORSION  OUTER CYLINDER SHOCK STRUT  FOR THE CYLINDER OUTER 
SHOCK 
A  SHOCK STRUT  STRUT 
INNER CYLINDER 
A 
B  B  C 
C 

PIN 1LOWER END CAP TORSION FWD ASSEMBLY BRACKET
LINK
WASHER FOR THE BOLT
ELECTRICAL APEX PIN 2 (HEAD CONDUIT
LOWER
OUTBOARD) BRACKET
TORSION BOLT
LINK
A-A
(2 LOCATIONS)
SPACER
UPPER
TORSION SPLINED
LINK WASHER
0.003-0.005 INCH COLLAR
CLEARANCE
BRACKET BOLT (4 LOCATIONS) NUT
ANTIROTATION BOLT
B-B
Torsion Links Installation for the Main Landing Gear Figure 401 (Sheet 1)

 32-11-16
 ALL  ú ú 02 Page 402 ú May 28/99
 
A
757 MAINTENANCE MANUAL
 S 014-034
 (3)  
Remove the strut door (AMM 32-12-04/401).

 S 584-003

 (4)  
Lift the airplane (AMM 07-11-01/201).

 S 014-004

 (5)  
Remove the forward wheels and the tires (AMM 32-45-01/401).

 E.
Remove the Torsion Links

 S 014-005
 (1)  
Remove the support bracket(s) for the electrical and the hydraulic lines from the upper torsion link.

 S 864-030

 (2)  
Hold the torsion links.

 S 034-007

 (3)
Remove the bracket bolts that are near the nut on the apex pin. This will disconnect the support bracket from the collar.

NUT
SHOCK STRUT INNER CYLINDER
PIN
INSTALL THE PIN WITH THE HEAD OUTBOARD
INSTALL THE PIN ON THE LEFT MAIN LANDING GEAR WITH THE HEAD INBOARD LOWER
INSTALL THE PIN ON THE RIGHT MAIN LANDING GEAR LINK
WITH THE HEAD OUTBOARD  ASSEMBLY

C-C (2 LOCATIONS)
Torsion Links Installation for the Main Landing Gear
Figure 401 (Sheet 2)

 32-11-16
 ALL  ú ú 05 Page 403 ú Dec 20/96
 
A

757
MAINTENANCE MANUAL

 (4)  S 034-008Pull the support bracket away from the head of the apex pin. This will disconnect the bracket from the torsion link (View B-B).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(109)