B.
Access
(1)
Location Zones
211/212 Control Cabin
731/741 Main Landing Gear (MLG)
732/742 MLG Body Doors
733/743 MLG Oleo Doors
C.
Prepare for the Removal of the Trunnion Fairing Door
S 494-014
WARNING: MAKE SURE THE DOWNLOCKS ARE INSTALLED ON THE NOSE AND MAIN
_______ LANDING GEAR BEFORE YOU MOVE THE CONTROL LEVER FOR THE LANDING GEAR. IF THE CONTROL LEVER IS MOVED WITHOUT THE DOWNLOCKS INSTALLED, THE LANDING GEAR CAN RETRACT AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1)
Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
S 864-003
(2)
Put the control lever for the landing gear in the OFF position. Attach a DO-NOT-OPERATE tag to the control lever.
D.
Remove the Trunnion Fairing Door
(1)
Hold the trunnion fairing door.
S 014-005
(2)
Remove the nuts (7), washers (4,6), bushings (5), and bolts (3) to disconnect the pushrod from the strut door and the trunnion door.
S 844-004
NOTE:____Do not loosen the jamnuts on the ends of the pushrod. It is important to keep the bearing locations relative to each other the same. This will permit you to use the old rod for a reference to adjust the new rod.
32-12-10
ALL ú ú 01 Page 401 ú May 28/99
A
757
MAINTENANCE MANUAL
SEE A
1. TRUNNION
FAIRING
DOOR
SEE B
INBD
FWD
FORWARD HINGE
BOLT
SEE C
STRUT DOOR
2. PUSH ROD
ASSEMBLY
SUPPORT
FITTING A
A ASSEMBLY
A AFT HINGE BOLT
A SEE C
A
TRUNNION FAIRING DOOR
B
Trunnion Fairing Door Installtion for the Main Landing Gear
Figure 401 (Sheet 1)
E85245
32-12-10
ALL ú ú 01 Page 402 ú May 28/99
A
757
MAINTENANCE MANUAL
3. BOLT
7. NUT
12. NUT
SUPPORT BEAM
FWD
Trunnion Fairing Door Installation for the Main Landing Gear
Figure 401 (Sheet 2)
32-12-10
ALL ú ú 01 Page 403 ú May 28/99
A
757 MAINTENANCE MANUAL
S 014-006
(3)
Remove the hinge bolts (9) to disconnect the door hinges from the support beam (Detail B).
S 024-007
(4)
Remove the trunnion fairing door (1).
TASK 32-12-10-404-008
3. Install the Trunnion Fairing Door for the Main Landing Gear (Fig. 401)
___________________________________________________________
A. Equipment
(1)
Tramco T930-0063 Pushrod Adjust Tool
Tramco, Inc.
Paine Field - Everett
Everett, Washington
B.
Parts
~.............................................................................. | AMM | | AIPC | ................. ............................. | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG| ITEM | ................................................................................ | 401 | 1 | Trunnion Fairing Door | 32-12-10 | 01 | 270,275 | | | 2 | Pushrod | | | 215 | | | 3 | Bolt | | | 185 | | | 4 | Washer | | | 195 | | | 5 | Bushing | | | 205,210 | | | 6 | Washer | | | 190 | | | 7 | Nut | | | 200 | | | 8 | Washer | | | 250 | | | 9 | Bolt | | | 245 | | | 10 | Washer | | | 255 | | | 11 | Bushing | | | 265 | | | 12 | Nut | | | 260 | 2......…........…..................................…...........…....…..........1
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(162)
