C.
Access
(1)
Location Zones
731/741 Main Landing Gear (MLG)
732/742 MLG Body Doors
733/743 MLG Oleo Doors
D.
Prepare for the Removal of the Reaction Link
S 494-002
(1) Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
S 494-027
WARNING: USE THE PROCEDURE IN AMM/32-00-15/201 TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
S 864-004
(3)
Remove the pressure from the left hydraulic system (AMM 29-11-00/201).
(4)
Lift the airplane (AMM 07-11-01/201).
S 584-005
32-11-10
ALL ú ú 01 Page 401 ú May 28/99
A
757 MAINTENANCE MANUAL
A A LINK REACTION B SEE A C C B SUPPORT LINK SIDE STRUT WASHER BOLT LINK REACTION FORWARD SUPPORT TRUNNION
ASSEMBLY DOWNLOCK
STRUT SHOCK UPPER SIDE STRUT STRUT LOWER SIDE WASHER NUT LINK REACTION
ANTIROTATION BOLT
INBD A-A
ANTIROTATION BOLT NUT BUSHING SPLINED UPPER SWIVEL PIN 1 PIN LINK REACTION BOLT LINK REACTION LINK SUPPORT END CAP (2 LOCATIONS)
REACTION LINK REACTION LINK NUT
B-B C-C
1 INSTALL THE PIN WITH THE HEAD INBOARD
Main Gear Reaction Link Installation Figure 401 (Sheet 1)
32-11-10
ALL ú ú 01 Page 402 ú May 28/99
A
757
MAINTENANCE MANUAL
CLAMP
D-D
INSTALL THE CLAMP STUD IN THE UP DIRECTION FOR LEFT AND RIGHT GEAR.
Main Gear Reaction Link Installation Figure 401 (Sheet 2)
H31315
32-11-10
ALL ú ú 01 Page 403 ú May 28/99
A
757 MAINTENANCE MANUAL
E. Remove the Reaction Link
S 224-030
(1)
Note the location of the clamps for the hydraulic line on the reaction link. Write it down.
S 034-006
(2)
Disconnect the clamps for the hydraulic line from the reaction link.
S 494-007
(3)
Install the hoist and the hoist adapter. Use the instructions supplied with the tools. Lift the hoist to release the pressure on the attach pins.
S 844-008
(4)
Hold the upper side strut to prevent its movement.
S 014-009
(5)
Remove the pin to disconnect the reaction link from the support link (View C-C).
S 034-010
(6)
Move the inboard end of the reaction link aft to provide clearance to remove the upper swivel pin.
S 034-011
(7)
Remove the nut with the crowfoot wrench. Install the thread protector.
S 014-012
(8)
Remove the pin to disconnect the reaction link from the upper swivel (View B-B).
S 014-013
(9)
Remove the bolt to disconnect the reaction link from the forward trunnion support (View A-A).
S 024-014
(10)
Lower the reaction link and remove it.
TASK 32-11-10-404-015
3. Install the Reaction Link for the Main Landing Gear (Fig. 401)
___________________________________________________
A. Equipment
(1)
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(101)
